السلام عليكم
جاني الجهاز شغال لكن عليه رمز القفل
الجهاز لا يدعم الظبط المصنعي مباشر لكن يحتاج للتفليش ومنه الظبط المصنعي
تم التفليش وانطفا الجهاز فقط يعمل الهزاز اعدت التفليش نفس المشكل
جربت اصدارات اخرى ونفس المشكل
هنا السجل للفائدة
كود:
Connect phone on selected interface...
Backup Certificates now...
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Read Uniq key data started...
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
-> Phone not found.. :(
Fetching failed!
Connect phone on selected interface...
Read fail...!
Connect phone on selected interface...
Reading Phone Info....
Connected phone - Error
Software ver : Error
IMEI : Error
XappVer : 000008F2
Ape Ver : Error
APE Var : Error
APE ADSP: Error
DSP Ver : Error
APE Test: Error
PPM : Error
CNT : Error
Product SN : Error
Product code : Error
Base Prd.code: Error
Module code : Error
Long Prod.SN : Error
Hardware info=======
HWID : Error
Retu : Error
Tahvo : Error
Battery: 0 mV
CMT BT: Error
APE BT: Error
APE HW: Error
LCDVer: Error
Lock info ===========
IMEI : Error
IMEI spNet :
IMEI svNet :
Unable to read Lock table... :(
Error collect lock info, try again
Error, when try do backup CRT308 :(
SDD key status : Error Read Info
CMLA Key status : Not Present
SimLock status : Damaged!!!!!
Security status : Damaged!!!!!
Reading Phone Info....
Connected phone - Error
Software ver : Error
IMEI : Error
XappVer : 000008F2
Ape Ver : Error
APE Var : Error
APE ADSP: Error
DSP Ver : Error
APE Test: Error
PPM : Error
CNT : Error
Product SN : Error
Product code : Error
Base Prd.code: Error
Module code : Error
Long Prod.SN : Error
Hardware info=======
HWID : Error
Retu : Error
Tahvo : Error
Battery: 0 mV
CMT BT: Error
APE BT: Error
APE HW: Error
LCDVer: Error
Lock info ===========
IMEI : Error
IMEI spNet :
IMEI svNet :
Unable to read Lock table... :(
Error collect lock info, try again
Error, when try do backup CRT308 :(
SDD key status : Error Read Info
CMLA Key status : Not Present
SimLock status : Damaged!!!!!
Security status : Damaged!!!!!
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Device boot not done
Check Drivers
Try again
Phone found!
Series 60 Device detected!
read info... - Ok
Connect phone on selected interface...
Read Uniq key data started...
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
-> Phone not found.. :(
Fetching failed!
Connect phone on selected interface...
Read fail...!
Connect phone on selected interface...
Phone found!
Series 60 Device detected!
read info... - Ok
Phone disconected!
Connect phone on selected interface...
Backup Certificates now...
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
-> Phone not found.. :(
Looks like ASIC not supported, or HW failure
Supported : RapuYamaVx, RAP3Gv4, BroadComm, RAPIDO, XG213, XG221, XG223, XG618
Phone found!
Series 60 Device detected!
read info... - Ok
Phone disconected!
Connect phone on selected interface...
-> Phone not found.. :(
Looks like ASIC not supported, or HW failure
Supported : RapuYamaVx, RAP3Gv4, BroadComm, RAPIDO, XG213, XG221, XG223, XG618
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : Manual
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm948__10.24.mcusw
PPM : rm948__10.24.ppm_m3
CNT : rm948__10.24.image_m3_059T320
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len : 0x16
IF xCPUID : XGOLD 618 [XMM6180 QUARK]
IF uCHIPID : 50A9070100030101E010040940049752480E19B6FFFF
IF Resp Data : 50A9070100030101
Wait for user action : Insert battery
Sending EBL Loader ...
EBL Loader Ok
EBL Loader ready
Sending EBL ...
EBL sent Ok
EBL : QUARK_1340.100_M1S1
QUARK EEP config Ok
FLASHID : 20004000 , [ MuxOneNAND ]
Boot conf set, Target Ready
Boot done!
Backup enabled, will read all certificates
RPL saved : D:\BST\BEST\Backup\Cert\_XG618_SIM.rpl
===Flashing [MCU]===
Processing file : rm948__10.24.mcusw
Region count : 8
00 : [ PSI ] : psi_flash_unsigned.fls
01 : [ BCore ] : slb_signed.fls
02 : [ Code ] : main_toc_signed.fls
03 : [ Code ] : rm948__10.24.mcusw_signed_mcusw.fls
04 : [ Code ] : swap_signed.fls
05 : [ Cust ] : dynsw.fls
06 : [ Code ] : aeneas_signed.fls
07 : [ Code ] : fota_signed.fls
Parse done , flashing now
Flash : 00 : psi_flash_unsigned.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x00090000 , Len : 0x00020000
Erase now...
Erase done
Region Start : 0x00090000 , Data Len : 0x00010FB0
Region Load done
Write done
psi_flash_unsigned.fls image flash done
Flash : 01 : slb_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0001 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60000000 , Len : 0x00040000
Erase now...
Erase done
Region Start : 0x60000000 , Data Len : 0x00040000
Region Load done
Write done
slb_signed.fls image flash done
Flash : 02 : main_toc_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0002 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60040000 , Len : 0x00000400
Erase now...
Erase done
Region Start : 0x60040000 , Data Len : 0x00000400
Region Load done
Write done
main_toc_signed.fls image flash done
Flash : 03 : rm948__10.24.mcusw_signed_mcusw.fls
Sending Sec-Pack
SecInfo Area : 0x0003 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62E00000 , Len : 0x01100000
Erase now...
Erase done
Erase area 0x01 , Start 0xFFF00000 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x62E00000 , Data Len : 0x00F5AFCC
Region Load done
Write done
rm948__10.24.mcusw_signed_mcusw.fls image flash done
Flash : 04 : swap_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0004 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80000000 , Len : 0x00F00000
Erase now...
Erase done
Region Start : 0x80000000 , Data Len : 0x00C278E0
Region Load done
Write done
swap_signed.fls image flash done
Flash : 05 : dynsw.fls
Sending Sec-Pack
SecInfo Area : 0x0005 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62080000 , Len : 0x00100000
Erase now...
Erase done
Region Start : 0x62080000 , Data Len : 0x00044000
Region Load done
Write done
dynsw.fls image flash done
Flash : 06 : aeneas_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0006 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x63F79C00 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x63F79C00 , Data Len : 0x00046870
Region Load done
Write done
aeneas_signed.fls image flash done
Flash : 07 : fota_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0007 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x61F00004 , Len : 0x0017FFFC
Erase now...
Erase done
Region Start : 0x61F00004 , Data Len : 0x00149A78
Region Load done
Write done
fota_signed.fls image flash done
===Flashing [PPM]===
Processing file : rm948__10.24.ppm_m3
Region count : 1
00 : [ Cust ] : package_m3.ppm_ebl_psi.fls
Parse done , flashing now
Flash : 00 : package_m3.ppm_ebl_psi.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80F00000 , Len : 0x00B00000
Erase now...
Erase done
Region Start : 0x80F00000 , Data Len : 0x00527994
Region Load done
Write done
package_m3.ppm_ebl_psi.fls image flash done
===Flashing [CNT]===
Processing file : rm948__10.24.image_m3_059T320
Region count : 1
00 : [ Cust ] : package_m3_059T320.image.fls
Parse done , flashing now
Flash : 00 : package_m3_059T320.image.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0xA1000000 , Len : 0x0C580000
Erase now...
Erase done
Erase area 0x01 , Start 0xAE000000 , Len : 0x00300000
Erase now...
Erase done
Region Start : 0xA1000000 , Data Len : 0x02013400
Region Load done
Write done
package_m3_059T320.image.fls image flash done
Flashing done!
Total flash time : 00:00:12
Reboot phone now...
- > AfterFlash Failed! :( Reason : Downgrade try or HW Error
Anyway - try reinsert battery and PowerUp phone manualy
Connect phone on selected interface...
Done!
Connect phone on selected interface...
Elapsed: 00:03:01
Connect phone on selected interface...
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : Manual
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm948__10.24.mcusw
PPM : rm948__10.24.ppm_m3
CNT : rm948__10.24.image_m3_059T320
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len : 0x16
IF xCPUID : XGOLD 618 [XMM6180 QUARK]
IF uCHIPID : 50A9070100030101E010040940049752480E19B6FFFF
IF Resp Data : 50A9070100030101
Wait for user action : Insert battery
Sending EBL Loader ...
EBL Loader Ok
EBL Loader ready
Sending EBL ...
EBL sent Ok
EBL : QUARK_1340.100_M1S1
QUARK EEP config Ok
FLASHID : 20004000 , [ MuxOneNAND ]
Boot conf set, Target Ready
Boot done!
Backup enabled, will read all certificates
RPL saved : D:\BST\BEST\Backup\Cert\_2nd_XG618_SIM.rpl
===Flashing [MCU]===
Processing file : rm948__10.24.mcusw
Region count : 8
00 : [ PSI ] : psi_flash_unsigned.fls
01 : [ BCore ] : slb_signed.fls
02 : [ Code ] : main_toc_signed.fls
03 : [ Code ] : rm948__10.24.mcusw_signed_mcusw.fls
04 : [ Code ] : swap_signed.fls
05 : [ Cust ] : dynsw.fls
06 : [ Code ] : aeneas_signed.fls
07 : [ Code ] : fota_signed.fls
Parse done , flashing now
Flash : 00 : psi_flash_unsigned.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x00090000 , Len : 0x00020000
Erase now...
Erase done
Region Start : 0x00090000 , Data Len : 0x00010FB0
Region Load done
Write done
psi_flash_unsigned.fls image flash done
Flash : 01 : slb_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0001 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60000000 , Len : 0x00040000
Erase now...
Erase done
Region Start : 0x60000000 , Data Len : 0x00040000
Region Load done
Write done
slb_signed.fls image flash done
Flash : 02 : main_toc_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0002 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60040000 , Len : 0x00000400
Erase now...
Erase done
Region Start : 0x60040000 , Data Len : 0x00000400
Region Load done
Write done
main_toc_signed.fls image flash done
Flash : 03 : rm948__10.24.mcusw_signed_mcusw.fls
Sending Sec-Pack
SecInfo Area : 0x0003 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62E00000 , Len : 0x01100000
Erase now...
Erase done
Erase area 0x01 , Start 0xFFF00000 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x62E00000 , Data Len : 0x00F5AFCC
Region Load done
Write done
rm948__10.24.mcusw_signed_mcusw.fls image flash done
Flash : 04 : swap_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0004 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80000000 , Len : 0x00F00000
Erase now...
Erase done
Region Start : 0x80000000 , Data Len : 0x00C278E0
Region Load done
Write done
swap_signed.fls image flash done
Flash : 05 : dynsw.fls
Sending Sec-Pack
SecInfo Area : 0x0005 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62080000 , Len : 0x00100000
Erase now...
Erase done
Region Start : 0x62080000 , Data Len : 0x00044000
Region Load done
Write done
dynsw.fls image flash done
Flash : 06 : aeneas_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0006 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x63F79C00 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x63F79C00 , Data Len : 0x00046870
Region Load done
Write done
aeneas_signed.fls image flash done
Flash : 07 : fota_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0007 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x61F00004 , Len : 0x0017FFFC
Erase now...
Erase done
Region Start : 0x61F00004 , Data Len : 0x00149A78
Region Load done
Write done
fota_signed.fls image flash done
===Flashing [PPM]===
Processing file : rm948__10.24.ppm_m3
Region count : 1
00 : [ Cust ] : package_m3.ppm_ebl_psi.fls
Parse done , flashing now
Flash : 00 : package_m3.ppm_ebl_psi.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80F00000 , Len : 0x00B00000
Erase now...
Erase done
Region Start : 0x80F00000 , Data Len : 0x00527994
Region Load done
Write done
package_m3.ppm_ebl_psi.fls image flash done
===Flashing [CNT]===
Processing file : rm948__10.24.image_m3_059T320
Region count : 1
00 : [ Cust ] : package_m3_059T320.image.fls
Parse done , flashing now
Flash : 00 : package_m3_059T320.image.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0xA1000000 , Len : 0x0C580000
Erase now...
Erase done
Erase area 0x01 , Start 0xAE000000 , Len : 0x00300000
Erase now...
Erase done
Region Start : 0xA1000000 , Data Len : 0x02013400
Region Load done
Write done
package_m3_059T320.image.fls image flash done
Flashing done!
Total flash time : 00:00:12
Reboot phone now...
- > AfterFlash Failed! :( Reason : Downgrade try or HW Error
Anyway - try reinsert battery and PowerUp phone manualy
Connect phone on selected interface...
Done!
Connect phone on selected interface...
Elapsed: 00:03:15
Connect phone on selected interface...
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : FullFlash
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm948__10.24.mcusw
PPM : rm948__10.24.ppm_m3
CNT : rm948__10.24.image_m3_059T320
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len : 0x16
IF xCPUID : XGOLD 618 [XMM6180 QUARK]
IF uCHIPID : 50A9070100030101E010040940049752480E19B6FFFF
IF Resp Data : 50A9070100030101
Wait for user action : Insert battery
Sending EBL Loader ...
EBL Loader Ok
EBL Loader ready
Sending EBL ...
EBL sent Ok
EBL : QUARK_1340.100_M1S1
QUARK EEP config Ok
FLASHID : 20004000 , [ MuxOneNAND ]
Boot conf set, Target Ready
Boot done!
Backup enabled, will read all certificates
RPL saved : D:\BST\BEST\Backup\Cert\_2nd_XG618_SIM.rpl
===Flashing [MCU]===
Processing file : rm948__10.24.mcusw
Region count : 8
00 : [ PSI ] : psi_flash_unsigned.fls
01 : [ BCore ] : slb_signed.fls
02 : [ Code ] : main_toc_signed.fls
03 : [ Code ] : rm948__10.24.mcusw_signed_mcusw.fls
04 : [ Code ] : swap_signed.fls
05 : [ Cust ] : dynsw.fls
06 : [ Code ] : aeneas_signed.fls
07 : [ Code ] : fota_signed.fls
Parse done , flashing now
Flash : 00 : psi_flash_unsigned.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x00090000 , Len : 0x00020000
Erase now...
Erase done
Region Start : 0x00090000 , Data Len : 0x00010FB0
Region Load done
Write done
psi_flash_unsigned.fls image flash done
Flash : 01 : slb_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0001 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60000000 , Len : 0x00040000
Erase now...
Erase done
Region Start : 0x60000000 , Data Len : 0x00040000
Region Load done
Write done
slb_signed.fls image flash done
Flash : 02 : main_toc_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0002 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60040000 , Len : 0x00000400
Erase now...
Erase done
Region Start : 0x60040000 , Data Len : 0x00000400
Region Load done
Write done
main_toc_signed.fls image flash done
Flash : 03 : rm948__10.24.mcusw_signed_mcusw.fls
Sending Sec-Pack
SecInfo Area : 0x0003 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62E00000 , Len : 0x01100000
Erase now...
Erase done
Erase area 0x01 , Start 0xFFF00000 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x62E00000 , Data Len : 0x00F5AFCC
Region Load done
Write done
rm948__10.24.mcusw_signed_mcusw.fls image flash done
Flash : 04 : swap_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0004 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80000000 , Len : 0x00F00000
Erase now...
Erase done
Region Start : 0x80000000 , Data Len : 0x00C278E0
Region Load done
Write done
swap_signed.fls image flash done
Flash : 05 : dynsw.fls
Sending Sec-Pack
SecInfo Area : 0x0005 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62080000 , Len : 0x00100000
Erase now...
Erase done
Region Start : 0x62080000 , Data Len : 0x00044000
Region Load done
Write done
dynsw.fls image flash done
Flash : 06 : aeneas_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0006 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x63F79C00 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x63F79C00 , Data Len : 0x00046870
Region Load done
Write done
aeneas_signed.fls image flash done
Flash : 07 : fota_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0007 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x61F00004 , Len : 0x0017FFFC
Erase now...
Erase done
Region Start : 0x61F00004 , Data Len : 0x00149A78
Region Load done
Write done
fota_signed.fls image flash done
===Flashing [PPM]===
Processing file : rm948__10.24.ppm_m3
Region count : 1
00 : [ Cust ] : package_m3.ppm_ebl_psi.fls
Parse done , flashing now
Flash : 00 : package_m3.ppm_ebl_psi.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80F00000 , Len : 0x00B00000
Erase now...
Erase done
Region Start : 0x80F00000 , Data Len : 0x00527994
Region Load done
Write done
package_m3.ppm_ebl_psi.fls image flash done
===Flashing [CNT]===
Processing file : rm948__10.24.image_m3_059T320
Region count : 1
00 : [ Cust ] : package_m3_059T320.image.fls
Parse done , flashing now
Flash : 00 : package_m3_059T320.image.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0xA1000000 , Len : 0x0C580000
Erase now...
Erase done
Erase area 0x01 , Start 0xAE000000 , Len : 0x00300000
Erase now...
Erase done
Region Start : 0xA1000000 , Data Len : 0x02013400
Region Load done
Write done
package_m3_059T320.image.fls image flash done
Flashing done!
Total flash time : 00:00:14
Reboot phone now...
- > AfterFlash Failed! :( Reason : Downgrade try or HW Error
Anyway - try reinsert battery and PowerUp phone manualy
Connect phone on selected interface...
Done!
Connect phone on selected interface...
Elapsed: 00:02:30
Connect phone on selected interface...
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : FullFlash
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm948__04.06.mcusw
PPM : rm948__04.06.ppm_m3
CNT : rm948__04.06.image_m3_059S6T2
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len : 0x16
IF xCPUID : XGOLD 618 [XMM6180 QUARK]
IF uCHIPID : 50A9070100030101E010040940049752480E19B6FFFF
IF Resp Data : 50A9070100030101
Wait for user action : Insert battery
Sending EBL Loader ...
EBL Loader Ok
EBL Loader ready
Sending EBL ...
EBL sent Ok
EBL : QUARK_1327.300_M1S1
QUARK EEP config Ok
FLASHID : 20004000 , [ MuxOneNAND ]
Boot conf set, Target Ready
Boot done!
Backup enabled, will read all certificates
RPL saved : D:\BST\BEST\Backup\Cert\_2nd_XG618_SIM.rpl
===Flashing [MCU]===
Processing file : rm948__04.06.mcusw
Region count : 8
00 : [ PSI ] : psi_flash_unsigned.fls
01 : [ BCore ] : slb_signed.fls
02 : [ Code ] : main_toc_signed.fls
03 : [ Code ] : rm948__04.06.mcusw_signed_mcusw.fls
04 : [ Code ] : swap_signed.fls
05 : [ Cust ] : dynsw.fls
06 : [ Code ] : aeneas_signed.fls
07 : [ Code ] : fota_signed.fls
Parse done , flashing now
Flash : 00 : psi_flash_unsigned.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x00090000 , Len : 0x00020000
Erase now...
Erase done
Region Start : 0x00090000 , Data Len : 0x00010FB0
Region Load done
Write done
psi_flash_unsigned.fls image flash done
Flash : 01 : slb_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0001 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60000000 , Len : 0x00040000
Erase now...
Erase done
Region Start : 0x60000000 , Data Len : 0x00040000
Region Load done
Write done
slb_signed.fls image flash done
Flash : 02 : main_toc_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0002 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60040000 , Len : 0x00000400
Erase now...
Erase done
Region Start : 0x60040000 , Data Len : 0x00000400
Region Load done
Write done
main_toc_signed.fls image flash done
Flash : 03 : rm948__04.06.mcusw_signed_mcusw.fls
Sending Sec-Pack
SecInfo Area : 0x0003 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62E00000 , Len : 0x01100000
Erase now...
Erase done
Erase area 0x01 , Start 0xFFF00000 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x62E00000 , Data Len : 0x00F3A664
Region Load done
Write done
rm948__04.06.mcusw_signed_mcusw.fls image flash done
Flash : 04 : swap_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0004 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80000000 , Len : 0x00F00000
Erase now...
Erase done
Region Start : 0x80000000 , Data Len : 0x00C22738
Region Load done
Write done
swap_signed.fls image flash done
Flash : 05 : dynsw.fls
Sending Sec-Pack
SecInfo Area : 0x0005 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62080000 , Len : 0x00100000
Erase now...
Erase done
Region Start : 0x62080000 , Data Len : 0x00044000
Region Load done
Write done
dynsw.fls image flash done
Flash : 06 : aeneas_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0006 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x63F79C00 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x63F79C00 , Data Len : 0x00046870
Region Load done
Write done
aeneas_signed.fls image flash done
Flash : 07 : fota_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0007 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x61F00004 , Len : 0x0017FFFC
Erase now...
Erase done
Region Start : 0x61F00004 , Data Len : 0x001464A4
Region Load done
Write done
fota_signed.fls image flash done
===Flashing [PPM]===
Processing file : rm948__04.06.ppm_m3
Region count : 1
00 : [ Cust ] : package_m3.ppm_ebl_psi.fls
Parse done , flashing now
Flash : 00 : package_m3.ppm_ebl_psi.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80F00000 , Len : 0x00B00000
Erase now...
Erase done
Region Start : 0x80F00000 , Data Len : 0x00526DF4
Region Load done
Write done
package_m3.ppm_ebl_psi.fls image flash done
===Flashing [CNT]===
Processing file : rm948__04.06.image_m3_059S6T2
Region count : 1
00 : [ Cust ] : package_m3_059S6T2.image.fls
Parse done , flashing now
Flash : 00 : package_m3_059S6T2.image.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0xA1000000 , Len : 0x0C580000
Erase now...
Erase done
Erase area 0x01 , Start 0xAE000000 , Len : 0x00300000
Erase now...
Erase done
Region Start : 0xA1000000 , Data Len : 0x01D92400
Region Load done
Write done
package_m3_059S6T2.image.fls image flash done
Flashing done!
Total flash time : 00:00:11
Reboot phone now...
- > AfterFlash Failed! :( Reason : Downgrade try or HW Error
Anyway - try reinsert battery and PowerUp phone manualy
Connect phone on selected interface...
Done!
Connect phone on selected interface...
Elapsed: 00:03:01
Connect phone on selected interface...
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : SafeFlash
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm948__04.06.mcusw
PPM : rm948__04.06.ppm_m3
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len : 0x16
IF xCPUID : XGOLD 618 [XMM6180 QUARK]
IF uCHIPID : 50A9070100030101E010040940049752480E19B6FFFF
IF Resp Data : 50A9070100030101
Wait for user action : Insert battery
Sending EBL Loader ...
EBL Loader Ok
EBL Loader ready
Sending EBL ...
EBL sent Ok
EBL : QUARK_1327.300_M1S1
QUARK EEP config Ok
FLASHID : 20004000 , [ MuxOneNAND ]
Boot conf set, Target Ready
Boot done!
Backup enabled, will read all certificates
RPL saved : D:\BST\BEST\Backup\Cert\_2nd_XG618_SIM.rpl
===Flashing [MCU]===
Processing file : rm948__04.06.mcusw
Region count : 8
00 : [ PSI ] : psi_flash_unsigned.fls
01 : [ BCore ] : slb_signed.fls
02 : [ Code ] : main_toc_signed.fls
03 : [ Code ] : rm948__04.06.mcusw_signed_mcusw.fls
04 : [ Code ] : swap_signed.fls
05 : [ Cust ] : dynsw.fls
06 : [ Code ] : aeneas_signed.fls
07 : [ Code ] : fota_signed.fls
Parse done , flashing now
Flash : 00 : psi_flash_unsigned.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x00090000 , Len : 0x00020000
Erase now...
Erase done
Region Start : 0x00090000 , Data Len : 0x00010FB0
Region Load done
Write done
psi_flash_unsigned.fls image flash done
Flash : 01 : slb_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0001 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60000000 , Len : 0x00040000
Erase now...
Erase done
Region Start : 0x60000000 , Data Len : 0x00040000
Region Load done
Write done
slb_signed.fls image flash done
Flash : 02 : main_toc_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0002 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60040000 , Len : 0x00000400
Erase now...
Erase done
Region Start : 0x60040000 , Data Len : 0x00000400
Region Load done
Write done
main_toc_signed.fls image flash done
Flash : 03 : rm948__04.06.mcusw_signed_mcusw.fls
Sending Sec-Pack
SecInfo Area : 0x0003 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62E00000 , Len : 0x01100000
Erase now...
Erase done
Erase area 0x01 , Start 0xFFF00000 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x62E00000 , Data Len : 0x00F3A664
Region Load done
Write done
rm948__04.06.mcusw_signed_mcusw.fls image flash done
Flash : 04 : swap_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0004 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80000000 , Len : 0x00F00000
Erase now...
Erase done
Region Start : 0x80000000 , Data Len : 0x00C22738
Region Load done
Write done
swap_signed.fls image flash done
Flash : 05 : dynsw.fls
Sending Sec-Pack
SecInfo Area : 0x0005 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62080000 , Len : 0x00100000
Erase now...
Erase done
Region Start : 0x62080000 , Data Len : 0x00044000
Region Load done
Write done
dynsw.fls image flash done
Flash : 06 : aeneas_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0006 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x63F79C00 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x63F79C00 , Data Len : 0x00046870
Region Load done
Write done
aeneas_signed.fls image flash done
Flash : 07 : fota_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0007 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x61F00004 , Len : 0x0017FFFC
Erase now...
Erase done
Region Start : 0x61F00004 , Data Len : 0x001464A4
Region Load done
Write done
fota_signed.fls image flash done
===Flashing [PPM]===
Processing file : rm948__04.06.ppm_m3
Region count : 1
00 : [ Cust ] : package_m3.ppm_ebl_psi.fls
Parse done , flashing now
Flash : 00 : package_m3.ppm_ebl_psi.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80F00000 , Len : 0x00B00000
Erase now...
Erase done
Region Start : 0x80F00000 , Data Len : 0x00526DF4
Region Load done
Write done
package_m3.ppm_ebl_psi.fls image flash done
Flashing done!
Total flash time : 00:00:04
Reboot phone now...
- > AfterFlash Failed! :( Reason : Downgrade try or HW Error
Anyway - try reinsert battery and PowerUp phone manualy
Connect phone on selected interface...
Done!
Connect phone on selected interface...
Elapsed: 00:03:28
Connect phone on selected interface...
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : Manual
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm948__06.01.mcusw
PPM : rm948__06.01.ppm_s3
CNT : rm948__06.01.image_s3_059T813
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len : 0x16
IF xCPUID : XGOLD 618 [XMM6180 QUARK]
IF uCHIPID : 50A9070100030101E010040940049752480E19B6FFFF
IF Resp Data : 50A9070100030101
Wait for user action : Insert battery
Sending EBL Loader ...
EBL Loader Ok
-> Boot fail...
Flashing failed...
Phone disconected!
Connect phone on selected interface...
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : Manual
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm948__06.01.mcusw
PPM : rm948__06.01.ppm_s3
CNT : rm948__06.01.image_s3_059T813
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len : 0x16
IF xCPUID : XGOLD 618 [XMM6180 QUARK]
IF uCHIPID : 50A9070100030101E010040940049752480E19B6FFFF
IF Resp Data : 50A9070100030101
Wait for user action : Insert battery
Sending EBL Loader ...
EBL Loader Ok
EBL Loader ready
Sending EBL ...
EBL sent Ok
EBL : QUARK_1340.100_M1S1
QUARK EEP config Ok
FLASHID : 20004000 , [ MuxOneNAND ]
Boot conf set, Target Ready
Boot done!
Backup enabled, will read all certificates
RPL saved : D:\BST\BEST\Backup\Cert\_2nd_XG618_SIM.rpl
===Flashing [MCU]===
Processing file : rm948__06.01.mcusw
Region count : 8
00 : [ PSI ] : psi_flash_unsigned.fls
01 : [ BCore ] : slb_signed.fls
02 : [ Code ] : main_toc_signed.fls
03 : [ Code ] : rm948__06.01.mcusw_signed_mcusw.fls
04 : [ Code ] : swap_signed.fls
05 : [ Cust ] : dynsw.fls
06 : [ Code ] : aeneas_signed.fls
07 : [ Code ] : fota_signed.fls
Parse done , flashing now
Flash : 00 : psi_flash_unsigned.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x00090000 , Len : 0x00020000
Erase now...
Erase done
Region Start : 0x00090000 , Data Len : 0x00010FB0
Region Load done
Write done
psi_flash_unsigned.fls image flash done
Flash : 01 : slb_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0001 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60000000 , Len : 0x00040000
Erase now...
Erase done
Region Start : 0x60000000 , Data Len : 0x00040000
Region Load done
Write done
slb_signed.fls image flash done
Flash : 02 : main_toc_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0002 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60040000 , Len : 0x00000400
Erase now...
Erase done
Region Start : 0x60040000 , Data Len : 0x00000400
Region Load done
Write done
main_toc_signed.fls image flash done
Flash : 03 : rm948__06.01.mcusw_signed_mcusw.fls
Sending Sec-Pack
SecInfo Area : 0x0003 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62E00000 , Len : 0x01100000
Erase now...
Erase done
Erase area 0x01 , Start 0xFFF00000 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x62E00000 , Data Len : 0x00F3F7F4
Region Load done
Write done
rm948__06.01.mcusw_signed_mcusw.fls image flash done
Flash : 04 : swap_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0004 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80000000 , Len : 0x00F00000
Erase now...
Erase done
Region Start : 0x80000000 , Data Len : 0x00C263D4
Region Load done
Write done
swap_signed.fls image flash done
Flash : 05 : dynsw.fls
Sending Sec-Pack
SecInfo Area : 0x0005 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62080000 , Len : 0x00100000
Erase now...
Erase done
Region Start : 0x62080000 , Data Len : 0x00044000
Region Load done
Write done
dynsw.fls image flash done
Flash : 06 : aeneas_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0006 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x63F79C00 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x63F79C00 , Data Len : 0x00046870
Region Load done
Write done
aeneas_signed.fls image flash done
Flash : 07 : fota_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0007 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x61F00004 , Len : 0x0017FFFC
Erase now...
Erase done
Region Start : 0x61F00004 , Data Len : 0x00149820
Region Load done
Write done
fota_signed.fls image flash done
===Flashing [PPM]===
Processing file : rm948__06.01.ppm_s3
Region count : 1
00 : [ Cust ] : package_s3.ppm_ebl_psi.fls
Parse done , flashing now
Flash : 00 : package_s3.ppm_ebl_psi.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80F00000 , Len : 0x00B00000
Erase now...
Erase done
Region Start : 0x80F00000 , Data Len : 0x007513FC
Region Load done
Write done
package_s3.ppm_ebl_psi.fls image flash done
===Flashing [CNT]===
Processing file : rm948__06.01.image_s3_059T813
Region count : 1
00 : [ Cust ] : package_s3_059T813.image.fls
Parse done , flashing now
Flash : 00 : package_s3_059T813.image.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0xA1000000 , Len : 0x0C580000
Erase now...
Erase done
Erase area 0x01 , Start 0xAE000000 , Len : 0x00300000
Erase now...
Erase done
Region Start : 0xA1000000 , Data Len : 0x01D78400
Region Load done
Write done
package_s3_059T813.image.fls image flash done
Flashing done!
Total flash time : 00:00:12
Reboot phone now...
-------AFTER FLASH BREAKED BY USER-------
- > AfterFlash Failed! :( Reason : Downgrade try or HW Error
Anyway - try reinsert battery and PowerUp phone manualy
Connect phone on selected interface...
Done!
Connect phone on selected interface...
Elapsed: 00:01:37
Connect phone on selected interface...
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : Manual
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm948__10.24.mcusw
PPM : rm948__10.24.ppm_s3
CNT : rm948__10.24.image_s3_059S5R8
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len : 0x16
IF xCPUID : XGOLD 618 [XMM6180 QUARK]
IF uCHIPID : 50A9070100030101E010040940049752480E19B6FFFF
IF Resp Data : 50A9070100030101
Wait for user action : Insert battery
Sending EBL Loader ...
EBL Loader Ok
EBL Loader ready
Sending EBL ...
EBL sent Ok
EBL : QUARK_1340.100_M1S1
QUARK EEP config Ok
FLASHID : 20004000 , [ MuxOneNAND ]
Boot conf set, Target Ready
Boot done!
Backup enabled, will read all certificates
RPL saved : D:\BST\BEST\Backup\Cert\_2nd_XG618_SIM.rpl
===Flashing [MCU]===
Processing file : rm948__10.24.mcusw
Region count : 8
00 : [ PSI ] : psi_flash_unsigned.fls
01 : [ BCore ] : slb_signed.fls
02 : [ Code ] : main_toc_signed.fls
03 : [ Code ] : rm948__10.24.mcusw_signed_mcusw.fls
04 : [ Code ] : swap_signed.fls
05 : [ Cust ] : dynsw.fls
06 : [ Code ] : aeneas_signed.fls
07 : [ Code ] : fota_signed.fls
Parse done , flashing now
Flash : 00 : psi_flash_unsigned.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x00090000 , Len : 0x00020000
Erase now...
Erase done
Region Start : 0x00090000 , Data Len : 0x00010FB0
Region Load done
Write done
psi_flash_unsigned.fls image flash done
Flash : 01 : slb_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0001 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60000000 , Len : 0x00040000
Erase now...
Erase done
Region Start : 0x60000000 , Data Len : 0x00040000
Region Load done
Write done
slb_signed.fls image flash done
Flash : 02 : main_toc_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0002 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60040000 , Len : 0x00000400
Erase now...
Erase done
Region Start : 0x60040000 , Data Len : 0x00000400
Region Load done
Write done
main_toc_signed.fls image flash done
Flash : 03 : rm948__10.24.mcusw_signed_mcusw.fls
Sending Sec-Pack
SecInfo Area : 0x0003 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62E00000 , Len : 0x01100000
Erase now...
Erase done
Erase area 0x01 , Start 0xFFF00000 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x62E00000 , Data Len : 0x00F5AFCC
Region Load done
Write done
rm948__10.24.mcusw_signed_mcusw.fls image flash done
Flash : 04 : swap_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0004 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80000000 , Len : 0x00F00000
Erase now...
Erase done
Region Start : 0x80000000 , Data Len : 0x00C278E0
Region Load done
Write done
swap_signed.fls image flash done
Flash : 05 : dynsw.fls
Sending Sec-Pack
SecInfo Area : 0x0005 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62080000 , Len : 0x00100000
Erase now...
Erase done
Region Start : 0x62080000 , Data Len : 0x00044000
Region Load done
Write done
dynsw.fls image flash done
Flash : 06 : aeneas_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0006 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x63F79C00 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x63F79C00 , Data Len : 0x00046870
Region Load done
Write done
aeneas_signed.fls image flash done
Flash : 07 : fota_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0007 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x61F00004 , Len : 0x0017FFFC
Erase now...
Erase done
Region Start : 0x61F00004 , Data Len : 0x00149A78
Region Load done
Write done
fota_signed.fls image flash done
===Flashing [PPM]===
Processing file : rm948__10.24.ppm_s3
Region count : 1
00 : [ Cust ] : package_s3.ppm_ebl_psi.fls
Parse done , flashing now
Flash : 00 : package_s3.ppm_ebl_psi.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80F00000 , Len : 0x00B00000
Erase now...
Erase done
Region Start : 0x80F00000 , Data Len : 0x00751C14
Region Load done
Write done
package_s3.ppm_ebl_psi.fls image flash done
===Flashing [CNT]===
Processing file : rm948__10.24.image_s3_059S5R8
Region count : 1
00 : [ Cust ] : package_s3_059S5R8.image.fls
Parse done , flashing now
Flash : 00 : package_s3_059S5R8.image.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0xA1000000 , Len : 0x0C580000
Erase now...
Erase done
Erase area 0x01 , Start 0xAE000000 , Len : 0x00300000
Erase now...
Erase done
Region Start : 0xA1000000 , Data Len : 0x0201E400
Region Load done
Write done
package_s3_059S5R8.image.fls image flash done
Flashing done!
Total flash time : 00:00:13
Reboot phone now...
-------AFTER FLASH BREAKED BY USER-------
- > AfterFlash Failed! :( Reason : Downgrade try or HW Error
Anyway - try reinsert battery and PowerUp phone manualy
Connect phone on selected interface...
Done!
Connect phone on selected interface...
Elapsed: 00:01:16
Connect phone on selected interface...
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : Manual
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm948__04.06.mcusw
PPM : rm948__04.06.ppm_m2
CNT : rm948__04.06.image_m2_059T534
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
-> Boot fail...
Flashing failed...
Phone disconected!
Connect phone on selected interface...
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : Manual
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm948__04.06.mcusw
PPM : rm948__04.06.ppm_m2
CNT : rm948__04.06.image_m2_059T534
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len : 0x16
IF xCPUID : XGOLD 618 [XMM6180 QUARK]
IF uCHIPID : 50A9070100030101E010040940049752480E19B6FFFF
IF Resp Data : 50A9070100030101
Wait for user action : Insert battery
Sending EBL Loader ...
EBL Loader Ok
EBL Loader ready
Sending EBL ...
EBL sent Ok
EBL : QUARK_1327.300_M1S1
QUARK EEP config Ok
FLASHID : 20004000 , [ MuxOneNAND ]
Boot conf set, Target Ready
Boot done!
Backup enabled, will read all certificates
RPL saved : D:\BST\BEST\Backup\Cert\_2nd_XG618_SIM.rpl
===Flashing [MCU]===
Processing file : rm948__04.06.mcusw
Region count : 8
00 : [ PSI ] : psi_flash_unsigned.fls
01 : [ BCore ] : slb_signed.fls
02 : [ Code ] : main_toc_signed.fls
03 : [ Code ] : rm948__04.06.mcusw_signed_mcusw.fls
04 : [ Code ] : swap_signed.fls
05 : [ Cust ] : dynsw.fls
06 : [ Code ] : aeneas_signed.fls
07 : [ Code ] : fota_signed.fls
Parse done , flashing now
Flash : 00 : psi_flash_unsigned.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x00090000 , Len : 0x00020000
Erase now...
Erase done
Region Start : 0x00090000 , Data Len : 0x00010FB0
Region Load done
Write done
psi_flash_unsigned.fls image flash done
Flash : 01 : slb_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0001 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60000000 , Len : 0x00040000
Erase now...
Erase done
Region Start : 0x60000000 , Data Len : 0x00040000
Region Load done
Write done
slb_signed.fls image flash done
Flash : 02 : main_toc_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0002 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60040000 , Len : 0x00000400
Erase now...
Erase done
Region Start : 0x60040000 , Data Len : 0x00000400
Region Load done
Write done
main_toc_signed.fls image flash done
Flash : 03 : rm948__04.06.mcusw_signed_mcusw.fls
Sending Sec-Pack
SecInfo Area : 0x0003 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62E00000 , Len : 0x01100000
Erase now...
Erase done
Erase area 0x01 , Start 0xFFF00000 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x62E00000 , Data Len : 0x00F3A664
Region Load done
Write done
rm948__04.06.mcusw_signed_mcusw.fls image flash done
Flash : 04 : swap_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0004 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80000000 , Len : 0x00F00000
Erase now...
Erase done
Region Start : 0x80000000 , Data Len : 0x00C22738
Region Load done
Write done
swap_signed.fls image flash done
Flash : 05 : dynsw.fls
Sending Sec-Pack
SecInfo Area : 0x0005 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62080000 , Len : 0x00100000
Erase now...
Erase done
Region Start : 0x62080000 , Data Len : 0x00044000
Region Load done
Write done
dynsw.fls image flash done
Flash : 06 : aeneas_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0006 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x63F79C00 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x63F79C00 , Data Len : 0x00046870
Region Load done
Write done
aeneas_signed.fls image flash done
Flash : 07 : fota_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0007 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x61F00004 , Len : 0x0017FFFC
Erase now...
Erase done
Region Start : 0x61F00004 , Data Len : 0x001464A4
Region Load done
Write done
fota_signed.fls image flash done
===Flashing [PPM]===
Processing file : rm948__04.06.ppm_m2
Region count : 1
00 : [ Cust ] : package_m2.ppm_ebl_psi.fls
Parse done , flashing now
Flash : 00 : package_m2.ppm_ebl_psi.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80F00000 , Len : 0x00B00000
Erase now...
Erase done
Region Start : 0x80F00000 , Data Len : 0x00533D6C
Region Load done
Write done
package_m2.ppm_ebl_psi.fls image flash done
===Flashing [CNT]===
Processing file : rm948__04.06.image_m2_059T534
Region count : 1
00 : [ Cust ] : package_m2_059T534.image.fls
Parse done , flashing now
Flash : 00 : package_m2_059T534.image.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0xA1000000 , Len : 0x0C580000
Erase now...
Erase done
Erase area 0x01 , Start 0xAE000000 , Len : 0x00300000
Erase now...
Erase done
Region Start : 0xA1000000 , Data Len : 0x01D7B400
Region Load done
Write done
package_m2_059T534.image.fls image flash done
Flashing done!
Total flash time : 00:00:12
Reboot phone now...
-------AFTER FLASH BREAKED BY USER-------
- > AfterFlash Failed! :( Reason : Downgrade try or HW Error
Anyway - try reinsert battery and PowerUp phone manualy
Connect phone on selected interface...
Done!
Connect phone on selected interface...
Elapsed: 00:01:37
Connect phone on selected interface...
Wrong data! Check if your ProductCode is correct!
If you NOT know what you doing here - use NaviManager instead!
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : Manual
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm948__06.01.mcusw
PPM : rm948__06.01.ppm_m3
CNT : rm948__06.01.image_m3_059V2N0
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len : 0x16
IF xCPUID : XGOLD 618 [XMM6180 QUARK]
IF uCHIPID : 50A9070100030101E010040940049752480E19B6FFFF
IF Resp Data : 50A9070100030101
Wait for user action : Insert battery
Sending EBL Loader ...
EBL Loader Ok
EBL Loader ready
Sending EBL ...
EBL sent Ok
EBL : QUARK_1340.100_M1S1
QUARK EEP config Ok
FLASHID : 20004000 , [ MuxOneNAND ]
Boot conf set, Target Ready
Boot done!
Backup enabled, will read all certificates
RPL saved : D:\BST\BEST\Backup\Cert\_2nd_XG618_SIM.rpl
===Flashing [MCU]===
Processing file : rm948__06.01.mcusw
Region count : 8
00 : [ PSI ] : psi_flash_unsigned.fls
01 : [ BCore ] : slb_signed.fls
02 : [ Code ] : main_toc_signed.fls
03 : [ Code ] : rm948__06.01.mcusw_signed_mcusw.fls
04 : [ Code ] : swap_signed.fls
05 : [ Cust ] : dynsw.fls
06 : [ Code ] : aeneas_signed.fls
07 : [ Code ] : fota_signed.fls
Parse done , flashing now
Flash : 00 : psi_flash_unsigned.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x00090000 , Len : 0x00020000
Erase now...
Erase done
Region Start : 0x00090000 , Data Len : 0x00010FB0
Region Load done
Write done
psi_flash_unsigned.fls image flash done
Flash : 01 : slb_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0001 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60000000 , Len : 0x00040000
Erase now...
Erase done
Region Start : 0x60000000 , Data Len : 0x00040000
Region Load done
Write done
slb_signed.fls image flash done
Flash : 02 : main_toc_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0002 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60040000 , Len : 0x00000400
Erase now...
Erase done
Region Start : 0x60040000 , Data Len : 0x00000400
Region Load done
Write done
main_toc_signed.fls image flash done
Flash : 03 : rm948__06.01.mcusw_signed_mcusw.fls
Sending Sec-Pack
SecInfo Area : 0x0003 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62E00000 , Len : 0x01100000
Erase now...
Erase done
Erase area 0x01 , Start 0xFFF00000 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x62E00000 , Data Len : 0x00F3F7F4
Region Load done
Write done
rm948__06.01.mcusw_signed_mcusw.fls image flash done
Flash : 04 : swap_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0004 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80000000 , Len : 0x00F00000
Erase now...
Erase done
Region Start : 0x80000000 , Data Len : 0x00C263D4
Region Load done
Write done
swap_signed.fls image flash done
Flash : 05 : dynsw.fls
Sending Sec-Pack
SecInfo Area : 0x0005 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62080000 , Len : 0x00100000
Erase now...
Erase done
Region Start : 0x62080000 , Data Len : 0x00044000
Region Load done
Write done
dynsw.fls image flash done
Flash : 06 : aeneas_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0006 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x63F79C00 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x63F79C00 , Data Len : 0x00046870
Region Load done
Write done
aeneas_signed.fls image flash done
Flash : 07 : fota_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0007 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x61F00004 , Len : 0x0017FFFC
Erase now...
Erase done
Region Start : 0x61F00004 , Data Len : 0x00149820
Region Load done
Write done
fota_signed.fls image flash done
===Flashing [PPM]===
Processing file : rm948__06.01.ppm_m3
Region count : 1
00 : [ Cust ] : package_m3.ppm_ebl_psi.fls
Parse done , flashing now
Flash : 00 : package_m3.ppm_ebl_psi.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80F00000 , Len : 0x00B00000
Erase now...
Erase done
Region Start : 0x80F00000 , Data Len : 0x00527138
Region Load done
Write done
package_m3.ppm_ebl_psi.fls image flash done
===Flashing [CNT]===
Processing file : rm948__06.01.image_m3_059V2N0
Region count : 1
00 : [ Cust ] : package_m3_059V2N0.image.fls
Parse done , flashing now
Flash : 00 : package_m3_059V2N0.image.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0xA1000000 , Len : 0x0C580000
Erase now...
Erase done
Erase area 0x01 , Start 0xAE000000 , Len : 0x00300000
Erase now...
Erase done
Region Start : 0xA1000000 , Data Len : 0x01D8B400
Region Load done
Write done
package_m3_059V2N0.image.fls image flash done
Flashing done!
Total flash time : 00:00:12
Reboot phone now...راسلت الفريق وعملت موضوع بالهوستنغ ولا رد من الفريق لمدة 3 ايام حتى قررت اني اشتري جهاز للزبون وفعلا اعطيته جهاز كان عندي
طبعا كنت في هم ليس بسبب الخسارة فقط ولكن بسبب الاحراج وايضا العمل ضعيف وهذه خسائر اضافيه
لكن والداي دائما يعلماني (من يضيع صلاته فقط هو من يخسر اما الاموال فانت بتجارة ومعرض للربح والخسارة )
المهم بعد ال 3 ايام وبعد صلاة الظهر دعوت الله ليهديني لحل المشكل
قرات عن جابر بن حيان عالم الكيمياء انه كان يستعين بقيام الليل ليحل معادلات الكيمياء
ومن تلقاء نفسي جربت اني افلش الاصدار المخصص للجهاز NOKIA 208 لكن RM 949
مالذي تبين هنا
ان الملصق اللي تحت البطاريه كان لجهاز RM 948 بشريحة واحدة بينما جهازي كان بشريحتين واحدة تحت البطارية والثانية جانبيه وكانها مكان بطاقة الذاكرة
اي ان ملصق الشركة كان بالغلط (جل من لايسهو ولا يخطئ)
ليعمل الجهاز بشكل طبيعي والحمدلله واتصلت بالزبون واعدت الجهاز له واعاد لي جهازي
هنا السجل بعد تصليح الهاتف
كود:
Connect phone on selected interface...
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : Manual
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm949__10.34_2.mcusw
PPM : rm949__10.34.ppm_q
CNT : rm949__10.34_2.image_q_059S5N1_059T368_208_05
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len : 0x16
IF xCPUID : XGOLD 618 [XMM6180 QUARK]
IF uCHIPID : 50A9070100030101E010040940049752480E19B6FFFF
IF Resp Data : 50A9070100030101
Wait for user action : Insert battery
Sending EBL Loader ...
EBL Loader Ok
EBL Loader ready
Sending EBL ...
EBL sent Ok
EBL : QUARK_1340.100_M1S1
QUARK EEP config Ok
FLASHID : 20004000 , [ MuxOneNAND ]
Boot conf set, Target Ready
Boot done!
Backup enabled, will read all certificates
Reading CCC
Reading HWC
Reading NPC
IMEI 1 :
IMEI 2 :
Phone Product Code : 059T3C3
NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...
RPL saved : E:\BEST\Backup\Cert\3 7_XG618_CRT.rpl
===Flashing [MCU]===
Processing file : rm949__10.34_2.mcusw
Region count : 8
00 : [ PSI ] : psi_flash_unsigned.fls
01 : [ BCore ] : slb_signed.fls
02 : [ Code ] : main_toc_signed.fls
03 : [ Code ] : rm949__10.34.mcusw_signed_mcusw.fls
04 : [ Code ] : swap_signed.fls
05 : [ Cust ] : dynsw.fls
06 : [ Code ] : aeneas_signed.fls
07 : [ Code ] : fota_signed.fls
Parse done , flashing now
Flash : 00 : psi_flash_unsigned.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x00090000 , Len : 0x00020000
Erase now...
Erase done
Region Start : 0x00090000 , Data Len : 0x00010FB0
Region Load done
Write done
psi_flash_unsigned.fls image flash done
Flash : 01 : slb_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0001 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60000000 , Len : 0x00040000
Erase now...
Erase done
Region Start : 0x60000000 , Data Len : 0x00040000
Region Load done
Write done
slb_signed.fls image flash done
Flash : 02 : main_toc_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0002 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60040000 , Len : 0x00000400
Erase now...
Erase done
Region Start : 0x60040000 , Data Len : 0x00000400
Region Load done
Write done
main_toc_signed.fls image flash done
Flash : 03 : rm949__10.34.mcusw_signed_mcusw.fls
Sending Sec-Pack
SecInfo Area : 0x0003 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62E00000 , Len : 0x01100000
Erase now...
Erase done
Erase area 0x01 , Start 0xFFF00000 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x62E00000 , Data Len : 0x00F5CAC4
Region Load done
Write done
rm949__10.34.mcusw_signed_mcusw.fls image flash done
Flash : 04 : swap_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0004 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80000000 , Len : 0x00F00000
Erase now...
Erase done
Region Start : 0x80000000 , Data Len : 0x00C2E6C4
Region Load done
Write done
swap_signed.fls image flash done
Flash : 05 : dynsw.fls
Sending Sec-Pack
SecInfo Area : 0x0005 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62080000 , Len : 0x00100000
Erase now...
Erase done
Region Start : 0x62080000 , Data Len : 0x00044000
Region Load done
Write done
dynsw.fls image flash done
Flash : 06 : aeneas_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0006 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x63F79C00 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x63F79C00 , Data Len : 0x00046870
Region Load done
Write done
aeneas_signed.fls image flash done
Flash : 07 : fota_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0007 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x61F00004 , Len : 0x0017FFFC
Erase now...
Erase done
Region Start : 0x61F00004 , Data Len : 0x00149A90
Region Load done
Write done
fota_signed.fls image flash done
===Flashing [PPM]===
Processing file : rm949__10.34.ppm_q
Region count : 1
00 : [ Cust ] : package_q.ppm_ebl_psi.fls
Parse done , flashing now
Flash : 00 : package_q.ppm_ebl_psi.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80F00000 , Len : 0x00B00000
Erase now...
Erase done
Region Start : 0x80F00000 , Data Len : 0x006D3220
Region Load done
Write done
package_q.ppm_ebl_psi.fls image flash done
===Flashing [CNT]===
Processing file : rm949__10.34_2.image_q_059S5N1_059T368_208_05
Region count : 1
00 : [ Cust ] : rm949__10.34.image_q_059S5N1_059T368_208_05.fls
Parse done , flashing now
Flash : 00 : rm949__10.34.image_q_059S5N1_059T368_208_05.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0xA1000000 , Len : 0x0C580000
Erase now...
Erase done
Erase area 0x01 , Start 0xAE000000 , Len : 0x00300000
Erase now...
Erase done
Region Start : 0xA1000000 , Data Len : 0x02143800
Region Load done
Write done
rm949__10.34.image_q_059S5N1_059T368_208_05.fls image flash done
Flashing done!
Total flash time : 00:00:13
Reboot phone now...
Reading Phone Info....
Connected phone - Nokia 208 Dual SIM
Software Info: V 10.34 13-03-14 RM-949 (c) Nokia
IMEI:
PPM version : V 10.34 13-03-14 RM-949 (c) Nokia Q
Product code: 059T3C3
Wait, when phone will be ready ...
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Processing After Flash Defaults...
FullFactorySet... Ok!
UserDataDefaultsSet...OK!
ServiceDefaultsSet... Ok!
LeaveDefaultsSet... Ok!
ProductTuneSet...OK!
SwUpgradeSet...OK!
Resetting LifeTimer
Reset Done!
Check and Upload User Certificates ...
Total - 58 certs
Certificates found, skip upload ...
===== WARNING =====
Battery voltage is NOT enough for start
===== WARNING =====
Set phone to Normal mode...
AfterFlash operations done ;D
Done!
Connect phone on selected interface...
Elapsed: 00:01:11
Connect phone on selected interface...
Phone found!
Series 40 Device detected!
read info... - Ok
Phone disconected!
Connect phone on selected interface...
Phone found!
Series 40 Device detected!
read info... - Ok
Phone disconected!
Connect phone on selected interface...
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : Manual
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm949__10.34.mcusw
PPM : rm949__10.34.ppm_m3
CNT : rm949__10.34.image_m3_059S5K9
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len : 0x16
IF xCPUID : XGOLD 618 [XMM6180 QUARK]
IF uCHIPID : 50A9070100030101E010040940049752480E19B6FFFF
IF Resp Data : 50A9070100030101
Wait for user action : Insert battery
Sending EBL Loader ...
EBL Loader Ok
EBL Loader ready
Sending EBL ...
EBL sent Ok
EBL : QUARK_1340.100_M1S1
QUARK EEP config Ok
FLASHID : 20004000 , [ MuxOneNAND ]
Boot conf set, Target Ready
Boot done!
Backup enabled, will read all certificates
Reading CCC
Reading HWC
Reading NPC
IMEI 1 :
IMEI 2 :
Phone Product Code : 059T3C3
NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...
RPL saved : E:\BEST\Backup\Cert\3 _2nd_XG618_CRT.rpl
===Flashing [MCU]===
Processing file : rm949__10.34.mcusw
Region count : 8
00 : [ PSI ] : psi_flash_unsigned.fls
01 : [ BCore ] : slb_signed.fls
02 : [ Code ] : main_toc_signed.fls
03 : [ Code ] : rm949__10.34.mcusw_signed_mcusw.fls
04 : [ Code ] : swap_signed.fls
05 : [ Cust ] : dynsw.fls
06 : [ Code ] : aeneas_signed.fls
07 : [ Code ] : fota_signed.fls
Parse done , flashing now
Flash : 00 : psi_flash_unsigned.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x00090000 , Len : 0x00020000
Erase now...
Erase done
Region Start : 0x00090000 , Data Len : 0x00010FB0
Region Load done
Write done
psi_flash_unsigned.fls image flash done
Flash : 01 : slb_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0001 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60000000 , Len : 0x00040000
Erase now...
Erase done
Region Start : 0x60000000 , Data Len : 0x00040000
Region Load done
Write done
slb_signed.fls image flash done
Flash : 02 : main_toc_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0002 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60040000 , Len : 0x00000400
Erase now...
Erase done
Region Start : 0x60040000 , Data Len : 0x00000400
Region Load done
Write done
main_toc_signed.fls image flash done
Flash : 03 : rm949__10.34.mcusw_signed_mcusw.fls
Sending Sec-Pack
SecInfo Area : 0x0003 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62E00000 , Len : 0x01100000
Erase now...
Erase done
Erase area 0x01 , Start 0xFFF00000 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x62E00000 , Data Len : 0x00F5CAC4
Region Load done
Write done
rm949__10.34.mcusw_signed_mcusw.fls image flash done
Flash : 04 : swap_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0004 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80000000 , Len : 0x00F00000
Erase now...
Erase done
Region Start : 0x80000000 , Data Len : 0x00C2E6C4
Region Load done
Write done
swap_signed.fls image flash done
Flash : 05 : dynsw.fls
Sending Sec-Pack
SecInfo Area : 0x0005 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62080000 , Len : 0x00100000
Erase now...
Erase done
Region Start : 0x62080000 , Data Len : 0x00044000
Region Load done
Write done
dynsw.fls image flash done
Flash : 06 : aeneas_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0006 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x63F79C00 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x63F79C00 , Data Len : 0x00046870
Region Load done
Write done
aeneas_signed.fls image flash done
Flash : 07 : fota_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0007 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x61F00004 , Len : 0x0017FFFC
Erase now...
Erase done
Region Start : 0x61F00004 , Data Len : 0x00149A90
Region Load done
Write done
fota_signed.fls image flash done
===Flashing [PPM]===
Processing file : rm949__10.34.ppm_m3
Region count : 1
00 : [ Cust ] : package_m3.ppm_ebl_psi.fls
Parse done , flashing now
Flash : 00 : package_m3.ppm_ebl_psi.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80F00000 , Len : 0x00B00000
Erase now...
Erase done
Region Start : 0x80F00000 , Data Len : 0x005316A8
Region Load done
Write done
package_m3.ppm_ebl_psi.fls image flash done
===Flashing [CNT]===
Processing file : rm949__10.34.image_m3_059S5K9
Region count : 1
00 : [ Cust ] : package_m3_059S5K9.image.fls
Parse done , flashing now
Flash : 00 : package_m3_059S5K9.image.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0xA1000000 , Len : 0x0C580000
Erase now...
Erase done
Erase area 0x01 , Start 0xAE000000 , Len : 0x00300000
Erase now...
Erase done
Region Start : 0xA1000000 , Data Len : 0x02121A00
Region Load done
Write done
package_m3_059S5K9.image.fls image flash done
Flashing done!
Total flash time : 00:00:12
Reboot phone now...
Reading Phone Info....
Connected phone - Nokia 208 Dual SIM
Software Info: V 10.34 13-03-14 RM-949 (c) Nokia
IMEI:
PPM version : V 10.34 13-03-14 RM-949 (c) Nokia M3
Product code: 059T3C3
Wait, when phone will be ready ...
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Processing After Flash Defaults...
FullFactorySet... Ok!
UserDataDefaultsSet...OK!
ServiceDefaultsSet... Ok!
LeaveDefaultsSet... Ok!
ProductTuneSet...OK!
SwUpgradeSet...OK!
Resetting LifeTimer
Check phone mode...
Phone in Test mode
Seting Local mode... wait...
Local mode set
Reset Done!
Check and Upload User Certificates ...
Total - 58 certs
Certificates found, skip upload ...
===== WARNING =====
Battery voltage is can be not enough for start
===== WARNING =====
Set phone to Normal mode...
AfterFlash operations done ;D
Done!
Connect phone on selected interface...
Elapsed: 00:01:34
Connect phone on selected interface...
