Warning. HOT UPDATE. EASY-JTAG 1.0.49 Update. M110S, M250S, LG CYON, EMMC improved


JTAG Tool news:
Added:
- support Samsung SHW-M110S (Read/Write/Easy Repair)
- support Samsung SHW-M250S (Read/Write/Easy Repair)
- support LG CYON KU4300 (Read/Write/Easy Repair)
- support Huawei E1732 USB Modem (Read/Write)
- support Huawei E173u USB Modem (Read/Write)
EMMC Tool news:
- Box firmware 1.46 / Improved eMMC Write Speed
- Added full decoding extCSD register , you can see ReadOnly flags etc.
.


P.S. Still need other JTAG?


[SPOILER="EMMC flags read log"] Successefuly connected to box on COM7
Box S/N: **************, ,FW Ver.: 01.46
Loading eMMC Addon Firmware...
Init EMMC...
EMMC CID: 45010053454D3034470033B670513007
EMMC ID: 0x0045
EMMC ****: SEM04G
EMMC CSD: D00F00320F5903FFFFFFFDFF924040C9
=============================================
Extended CSD rev 1.5 (MMC 4.41)
=============================================
Card Supported Command sets [S_CMD_SET: 0x01]
HPI Features [HPI_FEATURE: 0x01]:
implementation ****d on CMD13
Background operations support [BKOPS_SUPPORT: 0x01]
Background operations status [BKOPS_STATUS: 0x00]
1st Initialisation Time after programmed sector [INI_TIMEOUT_AP: 0x0a]
Power class for 52MHz, DDR at 3.6V [PWR_CL_DDR_52_360: 0x00]
Power class for 52MHz, DDR at 1.95V [PWR_CL_DDR_52_195: 0x00]
Minimum Performance for 8bit at 52MHz in DDR mode:
[MIN_PERF_DDR_W_8_52: 0x00]
[MIN_PERF_DDR_R_8_52: 0x00]
TRIM Multiplier [TRIM_MULT: 0x02]
Secure Feature support [SEC_FEATURE_SUPPORT: 0x15]
Secure Erase Multiplier [SEC_ERASE_MULT: 0x96]
Secure TRIM Multiplier [SEC_TRIM_MULT: 0x96]
Boot Information [BOOT_INFO: 0x07]
Device supports alternative boot method
Device supports dual data rate during boot
Device supports high speed timing during boot
Boot partition size [BOOT_SIZE_MULTI: 0x08]
Access size [ACC_SIZE: 0x06]
High-capacity erase unit size [HC_ERASE_GRP_SIZE: 0x04]
High-capacity erase timeout [ERASE_TIMEOUT_MULT: 0x01]
Reliable write sector count [REL_WR_SEC_C: 0x01]
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x04]
Sleep current (VCC) [S_C_VCC: 0x08]
Sleep current (VCCQ) [S_C_VCCQ: 0x07]
Sleep/awake timeout [S_A_TIMEOUT: 0x11]
Sector Count [SEC_COUNT: 0x00748000]
Minimum Write Performance for 8bit:
[MIN_PERF_W_8_52: 0x0a]
[MIN_PERF_R_8_52: 0x0a]
[MIN_PERF_W_8_26_4_52: 0x0a]
[MIN_PERF_R_8_26_4_52: 0x0a]
Minimum Write Performance for 4bit:
[MIN_PERF_W_4_26: 0x0a]
[MIN_PERF_R_4_26: 0x0a]
Power classes registers:
[PWR_CL_26_360: 0x00]
[PWR_CL_52_360: 0x00]
[PWR_CL_26_195: 0x00]
[PWR_CL_52_195: 0x00]
Partition switching timing [PARTITION_SWITCH_TIME: 0x01]
Out-of-interrupt busy timing [OUT_OF_INTERRUPT_TIME: 0x02]
Card Type [CARD_TYPE: 0x07]
CSD structure version [CSD_STRUCTURE: 0x02]
Command set [CMD_SET: 0x00]
Command set revision [CMD_SET_REV: 0x00]
Power class [POWER_CLASS: 0x00]
High-speed interface timing [HS_TIMING: 0x00]
Erased memory ******* [ERASED_MEM_CONT: 0x00]
Boot configuration bytes [PARTITION_CONFIG: 0x00]
Not boot enable
No access to boot partition
Boot config protection [BOOT_CONFIG_PROT: 0x00]
Boot bus Conditions [BOOT_BUS_CONDITIONS: 0x01]
High-density erase group definition [ERASE_GROUP_DEF: 0x00]
=============================================
Boot write protection status registers [BOOT_WP_STATUS]: 0x00
Boot Area Write protection [BOOT_WP]: 0x00
Power ReadOnly locking: possible
Permanent ReadOnly locking: possible
Read Only lock status: not locked
=============================================
User area write protection register [USER_WP]: 0x00
FW configuration [FW_CONFIG]: 0x01
RPMB Size [RPMB_SIZE_MULT]: 0x01
Write reliability setting register [WR_REL_SET]: 0x1f
Write reliability parameter register [WR_REL_PARAM]: 0x04
Enable background operations handshake [BKOPS_EN]: 0x00
H/W reset function [RST_N_FUNCTION]: 0x00
HPI management [HPI_MGMT]: 0x00
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Max Enhanced Area Size [MAX_ENH_SIZE_MULT]: 0x0000e6
Partitions attribute [PARTITIONS_ATTRIBUTE]: 0x00
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
General Purpose Partition Size
[GP_SIZE_MULT_4]: 0x000000
[GP_SIZE_MULT_3]: 0x000000
[GP_SIZE_MULT_2]: 0x000000
[GP_SIZE_MULT_1]: 0x000000
Enhanced User Data Area Size [ENH_SIZE_MULT]: 0x000000
Enhanced User Data Start Address [ENH_START_ADDR]: 0x000000
Bad Block Management mode [SEC_BAD_BLK_MGMNT]: 0x00
Writing file...C:\temp\EMMCZ\sboot.bin
Successefuly connected to box on COM7
Box S/N: **************, ,FW Ver.: 01.46
Loading eMMC Addon Firmware...
Init EMMC...
EMMC CID: 45010053454D3034470033B670513007
EMMC ID: 0x0045
EMMC ****: SEM04G
EMMC CSD: D00F00320F5903FFFFFFFDFF924040C9
Writing 0008e594 bytes to 00000000 ...ROM2
Write Speed: 203 kB/s
Done !!!
Reading dump to file...C:\temp\EMMCZ\sboot_check.bin
Successefuly connected to box on COM7
Box S/N: **************, ,FW Ver.: 01.46
Loading eMMC Addon Firmware...
Init EMMC...
EMMC CID: 45010053454D3034470033B670513007
EMMC ID: 0x0045
EMMC ****: SEM04G
EMMC CSD: D00F00320F5903FFFFFFFDFF924040C9
Reading 00100000 bytes from 00000000 ...ROM2
Read Speed: 242 kB/s
Done !!!
[/SPOILER]

Discuss
الروابط تظهر للاعضاء فقط