evertek m20 frp done CM2-SP2

walscow

عضو جديد
إنضم
17 أبريل 2016
المشاركات
4
مستوى التفاعل
4
النقاط
0
تم بفضل الله فورمات و تجاوز حماية قوقل evertek m20

لوغ العملية

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC7731E_BASE : SC7731E_eMMC_1GB_RS
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : 0x0002
FDL : Control transfered!

Boot Done!


Wipe Ok : UserData
Wipe Ok : Cache
Wipe Ok : FRP

Reconnect Power/Cable!

Done!
Elapsed: 00:00:32


التبويت يكون

CPU PLATFORM
SC7731E BASE
MODEL TYPE
SC7731E EMMC1GB RS
بالتوفيق
 

walscow

عضو جديد
إنضم
17 أبريل 2016
المشاركات
4
مستوى التفاعل
4
النقاط
0
رد: evertek m20 frp done CM2-SP2

سلام عليكم
لم تفلح معي اخي
card found : E76656d6 , v0151
infinity-box chinese miracle ii : Spd/usc module [sp2] v2.00r2


operation : Format fs / reset settings [ v2.00r2 ]
mode : Reset frp

1. Power off device, wait 10-15 seconds
2. Press and hold bookey ( 1 : Both vol , 2 : Vol+ , 3 : Vol- )
3. Insert cable in device!

Wait for device ...

Device connected!
Error : Protocol handshake failed!

Error : Fail to init protocol!
Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect power/cable!

Operation : Format fs / reset settings [ v2.00r2 ]
mode : Reset frp

1. Power off device, wait 10-15 seconds
2. Press and hold bookey ( 1 : Both vol , 2 : Vol+ , 3 : Vol- )
3. Insert cable in device!

Wait for device ...

Device connected!
Error : Protocol handshake failed!

Error : Fail to init protocol!
Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect power/cable!

Operation : Format fs / reset settings [ v2.00r2 ]
mode : Default [ reset settings + frp ]

1. Power off device, wait 10-15 seconds
2. Press and hold bookey ( 1 : Both vol , 2 : Vol+ , 3 : Vol- )
3. Insert cable in device!

Wait for device ...

Device connected!
Error : Protocol handshake failed!

Error : Fail to init protocol!
Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect power/cable!

Operation : Format fs / reset settings [ v2.00r2 ]
mode : Default [ reset settings + frp ]

1. Power off device, wait 10-15 seconds
2. Press and hold bookey ( 1 : Both vol , 2 : Vol+ , 3 : Vol- )
3. Insert cable in device!

Wait for device ...

Device connected!
Error : Protocol handshake failed!

Error : Fail to init protocol!
Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect power/cable!

Operation : Format fs / reset settings [ v2.00r2 ]
mode : Reset frp

1. Power off device, wait 10-15 seconds
2. Press and hold bookey ( 1 : Both vol , 2 : Vol+ , 3 : Vol- )
3. Insert cable in device!

Wait for device ...

Device connected!
Error : Protocol handshake failed!

Error : Fail to init protocol!
Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect power/cable!

Operation : Format fs / reset settings [ v2.00r2 ]
mode : Reset frp

1. Power off device, wait 10-15 seconds
2. Press and hold bookey ( 1 : Both vol , 2 : Vol+ , 3 : Vol- )
3. Insert cable in device!

Wait for device ...

Device connected!
Error : Protocol handshake failed!

Error : Fail to init protocol!
Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect power/cable!

Operation : Identify [ v2.00r2 ]

1. Power off device, wait 10-15 seconds
2. Press and hold bookey ( 1 : Both vol , 2 : Vol+ , 3 : Vol- )
3. Insert cable in device!

Wait for device ...

Device connected!
Error : Protocol handshake failed!

Error : Fail to init protocol!
Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect power/cable!

التبويت يكون

cpu platform
sc7731e base
model type
sc7731e emmc1gb rs
 

azizdj

عضو
إنضم
15 مايو 2018
المشاركات
6
مستوى التفاعل
0
النقاط
1
رد: evertek m20 frp done CM2-SP2

احسنت ممكن فلاشه خاصه به
 
أعلى