رد: Redmi note 9 frp reset+ mi account disable
Card found : 8ADE1078 , v0147
Infinity-Box [ Chinese Miracle ] MediaTek Service Module [ MTK ] v2.16
Load IDBase v729152 Ok!
Operation : Reset Settings/Format FS [ v2.16 ]
Mode : FRP [ RESET PROTECTION ]
1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...
PTFN : MediaTek PreLoader USB VCOM (Android) (COM61)
MODE : PRELOADER PORT
PORT : 61
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6753 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : LEGACY MTK
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : BROM|BL : 0xFF|0x01
BROM : PRELOADER PORT
MODE : 0_base : BASE_v2028 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6753
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : OK
eMMC : 150100525831424D42078A8CE05B168D
DAInf: 4 : 2 : 155
DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info
EMMC: 150100525831424D42078A8CE05B938D
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : RX1BMB
EMMC:
BOOT1 : 0x00400000 [ 4,00 MB ]
BOOT2 : 0x00400000 [ 4,00 MB ]
RPMB : 0x00400000 [ 4,00 MB ]
USER : 0x747C00000 [ 29,12 GB ]
SRAM: 0x00020000 [ 128,00 KB ]
DRAM: 0xC0000000 [ 3,00 GB ]
CHIP : MT6753 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000
RNID : 3F1AFD17D073B7E4A4582F3E15BF436C
STATUS : BLANK FLASH
BSTYLE : EMMC FLASH BOOT
DA : USB : HIGH-SPEED
Boot done!
ERR : 0xC0010001
ERR : ERROR
ERR : 0x00000000|0x00000000
Error : Failed erase block!
>>> Try select another format mode!
Reconnect Power/Cable!
Operation : Reset Settings/Format FS [ v2.16 ]
Mode : FULL FACTORY ( WIPE + FRP )
1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...
PTFN : MediaTek USB Port (COM29)
MODE : BOOTROM
PORT : 29
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6768 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Talbot
TYPE : MODERN RAPHAEL
BROM : MEID : F9D116B62AB136C524EC8B28F5E5EAC8
BROM : SecLevel : 0x000000E7
BROM : SecMode : SBC+SLA+SDA+EXT
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : Xiaomi : Helio [G70][G80] | Manual : Disabled
BROM : SOCID : B04425E642F9F2B7CC29585552E13BD1698366CFACC234C79053F295D069D578
BROM : ARB : ACTIVE : LOG : F0: 102B 0000 F3: 0000 0000 [0200] V0: 0000 0000 [0001]
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6768
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : 0x00000001 : DA SEND ERROR!
ERROR : BROM : DL MODE ERROR
INFO : BROM Level : SLA AUTH or AUTH required!
Error : Fail to init protocol!
>>> Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation!
Reconnect Power/Cable!
