تحية عطرة للمشرفين ولإدارة المنتدى وأعضائها الكرام
الطريقة الصحيحة لبرمجة ذاكرة "هاتف حامل للمعالج MTK" على Medusa Pro
في كثير من الاحيان يصادف التقني مشاكل في الذاكرة. اصبحت قابلة للقرائة فقط. اي عملية تفقد البوت... يجب استبدالها
test emmc by cm2mt2
على Medusa Pro. ذاكرة غير صالحة للكتابة
كود:
[LEFT]Welcome to Medusa Pro Software version 2.1.8.
Started.
Reader #0: Alcor Micro USB Smart Card Reader 0
Reader #1: Alcor Micro USB Smart Card Reader 1
Reader #2: Alcor Micro USB Smart Card Reader 2
Please disconnect battery and USB cable.
Model Settings:
Interface : eMMC
Voltage : 1.8V
Bus Mode : 1 bit
Bus speed : Auto
Connecting...
Device : [B][SIZE=3][COLOR="#0000FF"]Hynix eMMC HBG4a2[/COLOR][/SIZE][/B]
Page size : 512 B
Block size : 512 B
Block count : 61071360
Size : 29.12 GB (29820.00 MB)
---------------------------------------------------------------
CID Info
[B][SIZE=3][COLOR="#0000FF"]CID : 90014A484247346132[/COLOR][/SIZE][/B]D41FB19900344D
Manufacturer ID : 0X90
Device/BGA : BGA (Discrete embedded)
OEM/Application ID : 0X4A
Product name : HBG4a2
Product revision : 13.4
Product serial number : (hex) 1FB19900
Manufacturing date : 03/2017
---------------------------------------------------------------
CSD Info
CSD : D02701328F5903FFFFFFFFE78A400017
CSD structure : CSD version No. 1.2
SPEC version : 4.1, 4.2, 4.3, 4.4, 4.41, 4.5,
4.51, 5.0, 5.01, 5.1
Data read access time1: 15 ms
TRAN speed : 26 MHz
READ block length : 512 Bytes
WP group enable : YES
PERM_WRITE_PROTECT : NO
TMP_WRITE_PROTECT : NO
---------------------------------------------------------------
EXTCSD Info
Revision 1.8 (for MMC v5.1)
Erase block size : 512 Kbytes
Boot1 size : 4096 Kbytes
Boot2 size : 4096 Kbytes
RPMB size : 4096 Kbytes
Partition config : (0x48) 01001000
Boot partition enable : Boot partition 1
(Bus width = 1Bit)
Boot ACK : Boot acknowledge sent during boot operation Bit
Boot bus conditions : (0x00) 00000000
Boot bus width : x1 (sdr) or x4 (ddr) bus width in boot operation mode (default)
Reset boot bus conditions : Reset bus width to x1, single data rate and backward compatible timings after boot operation (default)
Boot mode : Use single data rate + backward compatible timings in boot operation (default)
RST_n function : (0x01) RST_n signal is permanently enabled
Partitioning support : Device supports partitioning features
Enhanced attribute : Device can have enhanced technological features in partitions and user data area.
Max enhanced data size: 15265792 Kbytes
Partitions attribute : 0x0
Part setting completed: 0x0
GP partition 1 size : 0 b
GP partition 2 size : 0 b
GP partition 3 size : 0 b
GP partition 4 size : 0 b
Enhanced area size : (0x0) 0 b
Enhanced area start : (0x0) 0 b
Backup EXT_CSD saved to file F:/Medusa Pro Software/EXT_CSD Backups/HBG4a2_24_12_2020_21_26_45.bin.
Connect successful.
---------------------------------------------------------------
SW: 2.1.8; FW: 1.24.
---------------------------------------------------------------
Searching Android build info...
Not found
---------------------------------------------------------------
Samsung eMMC only supports smart report operation!
DEVICE_LIFE_TIME_EST_TYP_B : 0% - 10% device life time used
DEVICE_LIFE_TIME_EST_TYP_A : 0% - 10% device life time used
PRE_EOL_INFO : Urgent
SW: 2.1.8; FW: 1.24.
---------------------------------------------------------------
Selected scatter file: F:/MEGAsync Downloads/Geant T3/Geant T3/MT6739_Android_Scatter.txt.
Scatter file type 2.
Opened input file: F:/MEGAsync Downloads/Geant T3/Geant T3/preloader_k39tv1_bsp.bin
Found 7 eMMC supported CID:
eMMC Vendor ID : 90 (Hynix eMMC)
eMMC Model ID : 4A01
eMMC Name : HAG4a2
eMMC CID : 90014A484147346132
eMMC Vendor ID : 70 (Pretec eMMC)
eMMC Model ID : 0001
eMMC Name : EH8EE8
eMMC CID : 700100454838454538
eMMC Vendor ID : 15 (Samsung eMMC)
eMMC Model ID : 0001
eMMC Name : QE63MB
eMMC CID : 150100514536334D42
eMMC Vendor ID : 15 (Samsung eMMC)
eMMC Model ID : 0001
eMMC Name : GX6BMB
eMMC CID : 150100475836424D42
eMMC Vendor ID : 70 (Pretec eMMC)
eMMC Model ID : 0001
eMMC Name : EHACEA
eMMC CID : 700100454841434541
eMMC Vendor ID : 13 (Micron eMMC)
eMMC Model ID : 4E01
eMMC Name : Q2J97V
eMMC CID : 13014E51324A393756
eMMC Vendor ID : 90 (Hynix eMMC)
eMMC Model ID : 4A01
[B][SIZE=3][COLOR="#0000FF"]eMMC Name : HBG4a2[/COLOR][/SIZE][/B]
[B][SIZE=3][COLOR="#0000FF"]eMMC CID : 90014A484247346132[/COLOR][/SIZE][/B]
Writing. Please wait...
Switched to boot area partition 1.
Writing partition preloader...
Write data verification is enabled.
Done.
Switched to user area.
Writing partition recovery... Done.
Writing partition expdb...
[B][SIZE=3][COLOR="#FF0000"]ERROR[012]: Write error.[/COLOR][/SIZE][/B]
At sector 0
Disconnected.
Please disconnect battery and USB cable.
[/LEFT]مثال على هاتف Geant T3_ 32GB_ MT6739
اول شيئ تقوم به هو سحب الـ Firmware للجهاز وبالاخص وملف الشبكة NVRAM وملف الـ preloader
بعدها نحضر ذاكرة صالحة. مع مراعاة رقم CID مهم جدا
يعني يجب ان يتوافق رقم CID الموجود على الـ eMMC مع ملف الـ preloader
لمعرفة ذلك ادخل على واجهة Medusa Pro الى eMMC Service الى Show info options الى Parse MTK preloader ندرج ملف preloader.*Bin
كود:
[LEFT][B][SIZE=2][COLOR="#0000FF"]Welcome to Medusa Pro Software version 2.1.8.
Started.
Reader #0: Alcor Micro USB Smart Card Reader 0
Reader #1: Generic EMV Smartcard Reader 0
Opened input file: I:/Other Firmware/GEANT/Geant T3/preloader_k39tv1_bsp.bin
Found 7 eMMC supported CID:
[COLOR="#FF0000"]eMMC Vendor ID : 90 (Hynix eMMC) الذاكرة الاصلية للهاتف Geant T3
eMMC Model ID : 4A01
eMMC Name : HAG4a2
eMMC CID : 90014A484147346132[/COLOR]
eMMC Vendor ID : 70 (Pretec eMMC)
eMMC Model ID : 0001
eMMC Name : EH8EE8
eMMC CID : 700100454838454538
[COLOR="#008000"]eMMC Vendor ID : 15 (Samsung eMMC) الذاكرة البديلة المتوفرة عندي
eMMC Model ID : 0001
eMMC Name : QE63MB
eMMC CID : 150100514536334D42[/COLOR]
eMMC Vendor ID : 15 (Samsung eMMC)
eMMC Model ID : 0001
eMMC Name : GX6BMB
eMMC CID : 150100475836424D42
eMMC Vendor ID : 70 (Pretec eMMC)
eMMC Model ID : 0001
eMMC Name : EHACEA
eMMC CID : 700100454841434541
eMMC Vendor ID : 13 (Micron eMMC)
eMMC Model ID : 4E01
eMMC Name : Q2J97V
eMMC CID : 13014E51324A393756
eMMC Vendor ID : 90 (Hynix eMMC)
eMMC Model ID : 4A01
eMMC Name : HBG4a2
eMMC CID : 90014A484247346132
[/COLOR][/SIZE][/B][/LEFT]او تستطيع التعديل على رقم CID من الـ Medusa Pro للذواكر المسرح لها التعديل
على الـ Medusa Pro نعمل Full Erase للذاكرة البديلة تم كتابة الـ Firmware عبر خاصية Factory repair
كود:
[LEFT][B][SIZE=2]Please disconnect battery and USB cable.
Model Settings:
Interface : eMMC
Voltage : 1.8V
Bus Mode : 1 bit
Bus speed : Auto
Connecting...
Device : [COLOR="#008000"]Samsung eMMC QE63MB[/COLOR]
Page size : 512 B
Block size : 512 B
Block count : 30535680
Size : 14.56 GB (14910.00 MB)
---------------------------------------------------------------
CID Info
CID : [COLOR="#008000"]150100514536334D42[/COLOR]031F7FE00E853B
Manufacturer ID : 0X15
Device/BGA : BGA (Discrete embedded)
OEM/Application ID : 0X00
Product name : QE63MB
Full name one from : KMQE60013M-B318
Product revision : 0.3
Product serial number : (hex) 1F7FE00E
Manufacturing date : 08/2018
---------------------------------------------------------------
CSD Info
CSD : D02701320F5903FFF6DBFFEF8E40400D
CSD structure : CSD version No. 1.2
SPEC version : 4.1, 4.2, 4.3, 4.4, 4.41, 4.5,
4.51, 5.0, 5.01, 5.1
Data read access time1: 15 ms
TRAN speed : 26 MHz
READ block length : 512 Bytes
WP group enable : YES
PERM_WRITE_PROTECT : NO
TMP_WRITE_PROTECT : NO
---------------------------------------------------------------
EXTCSD Info
Revision 1.8 (for MMC v5.1)
Erase block size : 512 Kbytes
Boot1 size : 4096 Kbytes
Boot2 size : 4096 Kbytes
RPMB size : 4096 Kbytes
Partition config : (0x48) 01001000
Boot partition enable : Boot partition 1
(Bus width = 1Bit)
Boot ACK : Boot acknowledge sent during boot operation Bit
Boot bus conditions : (0x00) 00000000
Boot bus width : x1 (sdr) or x4 (ddr) bus width in boot operation mode (default)
Reset boot bus conditions : Reset bus width to x1, single data rate and backward compatible timings after boot operation (default)
Boot mode : Use single data rate + backward compatible timings in boot operation (default)
RST_n function : (0x01) RST_n signal is permanently enabled
Partitioning support : Device supports partitioning features
Enhanced attribute : Device can have enhanced technological features in partitions and user data area.
Max enhanced data size: 7626752 Kbytes
Partitions attribute : 0x0
Part setting completed: 0x0
GP partition 1 size : 0 b
GP partition 2 size : 0 b
GP partition 3 size : 0 b
GP partition 4 size : 0 b
Enhanced area size : (0x0) 0 b
Enhanced area start : (0x0) 0 b
Backup EXT_CSD saved to file F:/Medusa Pro Software/EXT_CSD Backups/QE63MB_24_12_2020_22_05_18.bin.
Connect successful.
---------------------------------------------------------------
SW: 2.1.8; FW: 1.24.
P00: GPT (00000000, 00000040) 32 KB
P01: boot_para (00000040, 00000800) 1024 KB
P02: recovery (00000840, 0000C000) 24 MB
P03: para (0000C840, 00000400) 512 KB
P04: expdb (0000CC40, 0000A000) 20 MB
P05: frp (00016C40, 00000800) 1024 KB
P06: nvcfg (00017440, 00004000) 8 MB
P07: nvdata (0001B440, 00010000) 32 MB
P08: metadata (0002B440, 00010000) 32 MB
P09: protect1 (0003B440, 00004000) 8 MB
P10: protect2 (0003F440, 00004BC0) 9.469 MB
P11: seccfg (00044000, 00004000) 8 MB
P12: persist (00048000, 00018000) 48 MB
P13: sec1 (00060000, 00001000) 2048 KB
P14: proinfo (00061000, 00001800) 3072 KB
P15: md1img (00062800, 00020000) 64 MB
P16: md1dsp (00082800, 00008000) 16 MB
P17: spmfw (0008A800, 00000800) 1024 KB
P18: mcupmfw (0008B000, 00000800) 1024 KB
P19: gz1 (0008B800, 00008000) 16 MB
P20: gz2 (00093800, 00008000) 16 MB
P21: nvram (0009B800, 00002800) 5 MB
P22: lk (0009E000, 00000800) 1024 KB
P23: lk2 (0009E800, 00000800) 1024 KB
P24: loader_ext1 (0009F000, 00000080) 64 KB
P25: loader_ext2 (0009F080, 00000080) 64 KB
P26: boot (0009F100, 0000C000) 24 MB
P27: logo (000AB100, 00004000) 8 MB
P28: odmdtbo (000AF100, 00008000) 16 MB
P29: tee1 (000B7100, 00002800) 5 MB
P30: tee2 (000B9900, 00006700) 12.88 MB
P31: vendor (000C0000, 00114000) 552 MB
P32: system (001D4000, 005DC000) 3000 MB
P33: cache (007B0000, 000D8000) 432 MB
P34: userdata (00888000, 0148EFDF) 10.28 GB
P35: flashinfo (01D16FDF, 00008000) 16 MB
---------------------------------------------------------------
Searching Android build info...
Ok
Disk/Image size : a3e00000 bytes
Device sector size : 512 bytes
Partition offset : 1916928
Number of sectors : 6144000
Device Manufacturer : ACE
Build ID : O11019
Display Build ID : AS0418_V08_20180911
Release ID : 8.1.0
Device Model : URBAN 1
Device Name : URBAN_1
Architecture ABI : arm64-v8a
Architecture ABI List : arm64-v8a,armeabi-v7a,armeabi
Build Description : URBAN_1-user 8.1.0 O11019 1535457849 release-keys
---------------------------------------------------------------
[COLOR="#FF0000"]Erasing. Please wait[/COLOR][COLOR="#008000"]... Done[/COLOR].
SW: 2.1.8; FW: 1.24.
Smart report not valid!
DEVICE_LIFE_TIME_EST_TYP_B : 10% - 20% device life time used
DEVICE_LIFE_TIME_EST_TYP_A : 10% - 20% device life time used
PRE_EOL_INFO : Normal
SW: 2.1.8; FW: 1.24.
---------------------------------------------------------------
Selected scatter file: F:/MEGAsync Downloads/Geant T3/Geant T3/MT6739_Android_Scatter.txt.
Scatter file type 2.
Opened input file: F:/MEGAsync Downloads/Geant T3/Geant T3/preloader_k39tv1_bsp.bin
Found 7 eMMC supported CID:
eMMC Vendor ID : 90 (Hynix eMMC)
eMMC Model ID : 4A01
eMMC Name : HAG4a2
eMMC CID : 90014A484147346132
eMMC Vendor ID : 70 (Pretec eMMC)
eMMC Model ID : 0001
eMMC Name : EH8EE8
eMMC CID : 700100454838454538
[COLOR="#008000"]eMMC Vendor ID : 15 (Samsung eMMC)
eMMC Model ID : 0001
eMMC Name : QE63MB
eMMC CID : 150100514536334D42[/COLOR]
eMMC Vendor ID : 15 (Samsung eMMC)
eMMC Model ID : 0001
eMMC Name : GX6BMB
eMMC CID : 150100475836424D42
eMMC Vendor ID : 70 (Pretec eMMC)
eMMC Model ID : 0001
eMMC Name : EHACEA
eMMC CID : 700100454841434541
eMMC Vendor ID : 13 (Micron eMMC)
eMMC Model ID : 4E01
eMMC Name : Q2J97V
eMMC CID : 13014E51324A393756
eMMC Vendor ID : 90 (Hynix eMMC)
eMMC Model ID : 4A01
eMMC Name : HBG4a2
eMMC CID : 90014A484247346132
Writing. Please wait...
Writing MBR...[COLOR="#EE82EE"]Done[/COLOR].
Writing primary GPT...[COLOR="#EE82EE"]Done[/COLOR].
Writing secondary GPT...[COLOR="#EE82EE"]Done[/COLOR].
Switched to boot area partition 1.
Writing partition preloader...
Write data verification is enabled.
[COLOR="#EE82EE"]Done[/COLOR].
Switched to user area.
Writing partition recovery... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition expdb... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition md1img... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition md1dsp... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition spmfw... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition mcupmfw... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition gz1... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition gz2... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition lk... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition lk2... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition loader_ext1... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition loader_ext2... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition boot... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition logo... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition odmdtbo... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition tee1... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition tee2... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition vendor... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition system... [COLOR="#EE82EE"]Done[/COLOR].
Writing partition cache... [COLOR="#EE82EE"]Done[/COLOR].
Writing checksums...[COLOR="#EE82EE"]Done[/COLOR].
Writing finished.
SW: 2.1.8; FW: 1.24.
Disconnected.
Please disconnect battery and USB cable.
Model Settings:
Interface : eMMC
Voltage : 1.8V
Bus Mode : 1 bit
Bus speed : Auto
Connecting...
Device : [COLOR="#008000"]Samsung eMMC QE63MB[/COLOR]
Page size : 512 B
Block size : 512 B
Block count : 30535680
Size : 14.56 GB (14910.00 MB)
---------------------------------------------------------------
CID Info
CID : [COLOR="#008000"]150100514536334D42[/COLOR]031F7FE00E853B
Manufacturer ID : 0X15
Device/BGA : BGA (Discrete embedded)
OEM/Application ID : 0X00
Product name : QE63MB
Full name one from : KMQE60013M-B318
Product revision : 0.3
Product serial number : (hex) 1F7FE00E
Manufacturing date : 08/2018
---------------------------------------------------------------
CSD Info
CSD : D02701320F5903FFF6DBFFEF8E40400D
CSD structure : CSD version No. 1.2
SPEC version : 4.1, 4.2, 4.3, 4.4, 4.41, 4.5,
4.51, 5.0, 5.01, 5.1
Data read access time1: 15 ms
TRAN speed : 26 MHz
READ block length : 512 Bytes
WP group enable : YES
PERM_WRITE_PROTECT : NO
TMP_WRITE_PROTECT : NO
---------------------------------------------------------------
EXTCSD Info
Revision 1.8 (for MMC v5.1)
Erase block size : 512 Kbytes
Boot1 size : 4096 Kbytes
Boot2 size : 4096 Kbytes
RPMB size : 4096 Kbytes
Partition config : (0x48) 01001000
Boot partition enable : Boot partition 1
(Bus width = 1Bit)
Boot ACK : Boot acknowledge sent during boot operation Bit
Boot bus conditions : (0x00) 00000000
Boot bus width : x1 (sdr) or x4 (ddr) bus width in boot operation mode (default)
Reset boot bus conditions : Reset bus width to x1, single data rate and backward compatible timings after boot operation (default)
Boot mode : Use single data rate + backward compatible timings in boot operation (default)
RST_n function : (0x01) RST_n signal is permanently enabled
Partitioning support : Device supports partitioning features
Enhanced attribute : Device can have enhanced technological features in partitions and user data area.
Max enhanced data size: 7626752 Kbytes
Partitions attribute : 0x0
Part setting completed: 0x0
GP partition 1 size : 0 b
GP partition 2 size : 0 b
GP partition 3 size : 0 b
GP partition 4 size : 0 b
Enhanced area size : (0x0) 0 b
Enhanced area start : (0x0) 0 b
Backup EXT_CSD saved to file F:/Medusa Pro Software/EXT_CSD Backups/QE63MB_24_12_2020_22_34_39.bin.
Connect successful.
---------------------------------------------------------------
SW: 2.1.8; FW: 1.24.
P00: GPT (00000000, 00000040) 32 KB
P01: boot_para (00000040, 00000800) 1024 KB
P02: recovery (00000840, 0000C000) 24 MB
P03: para (0000C840, 00000400) 512 KB
P04: expdb (0000CC40, 0000A000) 20 MB
P05: frp (00016C40, 00000800) 1024 KB
P06: nvcfg (00017440, 00004000) 8 MB
P07: nvdata (0001B440, 00010000) 32 MB
P08: metadata (0002B440, 00010000) 32 MB
P09: protect1 (0003B440, 00004000) 8 MB
P10: protect2 (0003F440, 00004BC0) 9.469 MB
P11: seccfg (00044000, 00004000) 8 MB
P12: sec1 (00048000, 00001000) 2048 KB
P13: proinfo (00049000, 00001800) 3072 KB
P14: md1img (0004A800, 00020000) 64 MB
P15: md1dsp (0006A800, 00008000) 16 MB
P16: spmfw (00072800, 00000800) 1024 KB
P17: mcupmfw (00073000, 00000800) 1024 KB
P18: gz1 (00073800, 00008000) 16 MB
P19: gz2 (0007B800, 00008000) 16 MB
P20: nvram (00083800, 00002800) 5 MB
P21: lk (00086000, 00000800) 1024 KB
P22: lk2 (00086800, 00000800) 1024 KB
P23: loader_ext1 (00087000, 00000080) 64 KB
P24: loader_ext2 (00087080, 00000080) 64 KB
P25: boot (00087100, 0000C000) 24 MB
P26: logo (00093100, 00004000) 8 MB
P27: odmdtbo (00097100, 00008000) 16 MB
P28: tee1 (0009F100, 00002800) 5 MB
P29: tee2 (000A1900, 00006700) 12.88 MB
P30: vendor (000A8000, 00114000) 552 MB
P31: system (001BC000, 00500000) 2560 MB
P32: cache (006BC000, 000D8000) 432 MB
P33: userdata (00794000, 032A1FDF) 25.32 GB
P34: flashinfo (03A35FDF, 00008000) 16 MB
---------------------------------------------------------------
Searching Android build info...
Ok
Disk/Image size : a3e00000 bytes
Device sector size : 512 bytes
Partition offset : 1818624
Number of sectors : 5242880
Device Manufacturer : [COLOR="#0000FF"]GEANT[/COLOR]
Build ID : O11019
Display Build ID : [COLOR="#0000FF"]GEANT_T3_V05_20181022[/COLOR]
Release ID : [COLOR="#0000FF"]8.1.0[/COLOR]
Device Model : [COLOR="#0000FF"]GEANT_T3[/COLOR]
Device Name : [COLOR="#0000FF"]GEANT_T3[/COLOR]
Architecture ABI : armeabi-v7a
Architecture ABI2 : armeabi
Architecture ABI List : armeabi-v7a,armeabi
Build Description : [COLOR="#0000FF"]full_k39tv1_bsp-user 8.1.0 O11019 1538194915 release-keys[/COLOR]
---------------------------------------------------------------
Disconnected.
[/SIZE][/B][/LEFT]
مثال على هاتف Samsung G532F
كود:
[LEFT][B][SIZE=3][COLOR="#0000FF"]
Found 4 eMMC supported CID:
eMMC Vendor ID : 15 (Samsung eMMC)
eMMC Model ID : 0001
eMMC Name : QN16MB
eMMC CID : 150100514E31364D42
[COLOR="#FF0000"]eMMC Vendor ID : 90 (Hynix eMMC) ملف [URL="https://www.dzgsm.com/vb/threads/83062-g532f-medusa-pro/?p=441607#post441607"]SRF[/URL]
eMMC Model ID : 4A01
eMMC Name : H8G4u
eMMC CID : 90014A483847347592[/COLOR]
eMMC Vendor ID : 15 (Samsung eMMC)
eMMC Model ID : 0001
eMMC Name : FN12MB
eMMC CID : 150100464E31324D42
eMMC Vendor ID : 15 (Samsung eMMC) ملف [URL="https://www.dzgsm.com/vb/threads/83062-g532f-medusa-pro/?p=441588&viewfull=1#post441588"]SRF[/URL]
eMMC Model ID : 0001
eMMC Name : QN16BB
eMMC CID : 150100514E31364242[/COLOR][/SIZE][/B][/LEFT]CID : 90014A48384734759201037958152555
متوافف مع G532FXXU1APL Firmware
CID : 150100514E3136424200AB5AAC5714CD
متوافف مع G532FXWU1ASB1 Firmware
الخلاصة: لتصليح البوت هواتف MTK يجب ان يتوافق رقم الـ CID الموجود على eMMC مع ملف الـ preloader
برمجة ذاكرة هاتف Medusa Pro �� Programming eMMC LG K11 Plus ��
تم بعون الله
