تم الحل فتح قفل الشاشة و frp لهاتف اوبو a12

cst_repair

:: عضو مميز ::
إنضم
2 يونيو 2013
المشاركات
280
مستوى التفاعل
370
النقاط
63
الإقامة
الجزائر الحبيبة
تم بفضل الله تخطي قفل الشاشة و FRP باستخدام ايزي حيثاج الكلاسيكية V1 لهاتف اوبو A12 CPH2083 والحمد لله




كود:
Z3X EasyJtag Software ver. 3.7.0.20
Loading eMMC GEN1 Firmware... IO: 2800 mV
Box S/N: 08FF4010780CCB57, ,FW Ver.: 01.63
CMD Pullup Level:2010 mV
CMD Active Level:2371 mV
Box IO Level:2800 mV
CLK Rate:1000 kHz
Bus Width:1bit,SDR
HiPower mode is ON!
Can't init device, Reason: CARD Ready Timeout Error 
Done.

Z3X EasyJtag Software ver. 3.7.0.20
Loading eMMC GEN1 Firmware... IO: 2800 mV
Box S/N: 08FF4010780CCB57, ,FW Ver.: 01.63
CMD Pullup Level:2021 mV
CMD Active Level:2371 mV
Box IO Level:2800 mV
CLK Rate:1000 kHz
Bus Width:1bit,SDR
HiPower mode is ON!
---------- eMMC Device Information ----------

eMMC CID : 90014A68423861503E0351C43EDFC6B2
eMMC CSD : D02700328F5903FFFFFFFFEF8E400042
eMMC Manufacturer ID: 0090 , OEM ID: 014A
eMMC Date: 12/2019  Rev.0x3
eMMC NAME: hB8aP> , S/N: 1371815647
eMMC NAME (HEX): 68423861503E 
EMMC ROM1 (Main User Data)   Capacity: 29820 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 kB
RPMB Info  mmc_switch_part Error, Reason: CARD Ready Timeout Error 
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
  Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x02 , width 8bits  , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
 Device support partitioning feature
 Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: hB8aP>_1371815647_20201023_2206.extcsd
Found valid GPT with protective MBR; using GPT.
Real (Hardware) Disk/Image size: 3A3E000 sectors 29.1 GiB 
Soft (Partitioned) Disk/Image size: 3A3DFBC sectors 29.1 GiB 
Disk identifier (GUID): 00000000-0000-0000-0000-000000000000
Logical sector size: 0x200  bytes ,First/Last usable sector: 34,61071326
Partition info successfully found
------ Detected 42 partitions ------
P0 (BOOT_PARA) [0x8000 0x100000] Size: 1.0MB
P1 (RECOVERY) [0x108000 0x4000000] Size: 64.0MB
P2 (PARA) [0x4108000 0x80000] Size: 512.0KB
P3 (OPPORESERVE1) [0x4188000 0x800000] Size: 8.0MB
P4 (OPPORESERVE2) [0x4988000 0x4000000] Size: 64.0MB
P5 (OPPORESERVE3) [0x8988000 0x4000000] Size: 64.0MB
P6 (OPPO_CUSTOM) [0xc988000 0x100000] Size: 1.0MB
P7 (EXPDB) [0xca88000 0x1400000] Size: 20.0MB
P8 (FRP) [0xde88000 0x100000] Size: 1.0MB
P9 (NVCFG) [0xdf88000 0x2000000] Size: 32.0MB
P10 (NVDATA) [0xff88000 0x4000000] Size: 64.0MB
P11 (METADATA) [0x13f88000 0x2000000] Size: 32.0MB
P12 (PROTECT1) [0x15f88000 0x800000] Size: 8.0MB
P13 (PROTECT2) [0x16788000 0x878000] Size: 8.468MB
P14 (SECCFG) [0x17000000 0x800000] Size: 8.0MB
P15 (PERSIST) [0x17800000 0x3000000] Size: 48.0MB
P16 (SEC1) [0x1a800000 0x200000] Size: 2.0MB
P17 (PROINFO) [0x1aa00000 0x300000] Size: 3.0MB
P18 (MD1IMG) [0x1ad00000 0x6400000] Size: 100.0MB
P19 (SPMFW) [0x21100000 0x100000] Size: 1.0MB
P20 (SCP1) [0x21200000 0x100000] Size: 1.0MB
P21 (SCP2) [0x21300000 0x100000] Size: 1.0MB
P22 (SSPM_1) [0x21400000 0x100000] Size: 1.0MB
P23 (SSPM_2) [0x21500000 0x100000] Size: 1.0MB
P24 (GZ1) [0x21600000 0x1000000] Size: 16.0MB
P25 (GZ2) [0x22600000 0x1000000] Size: 16.0MB
P26 (NVRAM) [0x23600000 0x4000000] Size: 64.0MB
P27 (LK) [0x27600000 0x500000] Size: 5.0MB
P28 (LK2) [0x27b00000 0x500000] Size: 5.0MB
P29 (BOOT) [0x28000000 0x2000000] Size: 32.0MB
P30 (LOGO) [0x2a000000 0x1000000] Size: 16.0MB
P31 (DTBO) [0x2b000000 0x1000000] Size: 16.0MB
P32 (TEE1) [0x2c000000 0x500000] Size: 5.0MB
P33 (TEE2) [0x2c500000 0xb00000] Size: 11.0MB
P34 (ODM) [0x2d000000 0x10000000] Size: 256.0MB
P35 (VENDOR) [0x3d000000 0x46000000] Size: 1.93GB
P36 (SYSTEM) [0x83000000 0x180000000] Size: 6.0GB
P37 (VBMETA) [0x203000000 0x800000] Size: 8.0MB
P38 (CACHE) [0x203800000 0x1b000000] Size: 432.0MB
P39 (USERDATA) [0x21e800000 0x5258fbe00] Size: 20.585GB
P40 (OTP) [0x7440fbe00 0x2b00000] Size: 43.0MB
P41 (FLASHINFO) [0x746bfbe00 0x1000000] Size: 16.0MB
------------------------------------
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x0083000000 (6.0GB)
Short EXT fs info:
Size: 5.904GB
Block size: 4.0KB
Inode size: 256
Inodes: 387072
Short Android info:
Unable to read prop.plist , code : 2
---------------------------------------------
Detected USERDATA USERDATA : 0x021E800000 (20.585GB)
Unable to mount USERDATA , code : 95
Userdata Superblock contents::
 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000     ................................;
 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000     ................................;
 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000     ................................;
 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000     ................................;
 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000     ................................;
 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000     ................................;
 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000     ................................;
 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000     ................................;
Done.

Running:Reset PIN/PASS/GESTURE Locks
Z3X EasyJtag Software ver. 3.7.0.20
Loading eMMC GEN1 Firmware... IO: 2800 mV
Box S/N: 08FF4010780CCB57, ,FW Ver.: 01.63
CMD Pullup Level:2000 mV
CMD Active Level:2361 mV
Box IO Level:2800 mV
CLK Rate:1000 kHz
Bus Width:1bit,SDR
HiPower mode is ON!
---------- eMMC Device Information ----------

eMMC CID : 90014A68423861503E0351C43EDFC6B2
eMMC CSD : D02700328F5903FFFFFFFFEF8E400042
eMMC Manufacturer ID: 0090 , OEM ID: 014A
eMMC Date: 12/2019  Rev.0x3
eMMC NAME: hB8aP> , S/N: 1371815647
eMMC NAME (HEX): 68423861503E 
EMMC ROM1 (Main User Data)   Capacity: 29820 MB , 0x3A3E000 pages , 0x747C00000 bytes
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 kB
RPMB Info  mmc_switch_part Error, Reason: CARD Ready Timeout Error 
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
  Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x02 , width 8bits  , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
 Device support partitioning feature
 Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Found valid GPT with protective MBR; using GPT.
Real (Hardware) Disk/Image size: 3A3E000 sectors 29.1 GiB 
Soft (Partitioned) Disk/Image size: 3A3DFBC sectors 29.1 GiB 
Disk identifier (GUID): 00000000-0000-0000-0000-000000000000
Logical sector size: 0x200  bytes ,First/Last usable sector: 34,61071326
Partition info successfully found
------ Android information ------
Detected LINUX(Android) USERDATA : 0x021E800000 (20.585GB)
Mount EXT4 fs...
Unable to mount USER , code : 95
---------------------------------------------
Done.

Running:Format FRP Partition...
Z3X EasyJtag Software ver. 3.7.0.20
Loading eMMC GEN1 Firmware... IO: 2800 mV
Box S/N: 08FF4010780CCB57, ,FW Ver.: 01.63
CMD Pullup Level:2010 mV
CMD Active Level:2609 mV
Box IO Level:2800 mV
CLK Rate:1000 kHz
Bus Width:1bit,SDR
HiPower mode is ON!
---------- eMMC Device Information ----------

eMMC CID : 90014A68423861503E0351C43EDFC6B2
eMMC CSD : D02700328F5903FFFFFFFFEF8E400042
eMMC Manufacturer ID: 0090 , OEM ID: 014A
eMMC Date: 12/2019  Rev.0x3
eMMC NAME: hB8aP> , S/N: 1371815647
eMMC NAME (HEX): 68423861503E 
EMMC ROM1 (Main User Data)   Capacity: 29820 MB , 0x3A3E000 pages , 0x747C00000 bytes
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 kB
RPMB Info  mmc_switch_part Error, Reason: CARD Ready Timeout Error 
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
  Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x02 , width 8bits  , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
 Device support partitioning feature
 Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Found valid GPT with protective MBR; using GPT.
Real (Hardware) Disk/Image size: 3A3E000 sectors 29.1 GiB 
Soft (Partitioned) Disk/Image size: 3A3DFBC sectors 29.1 GiB 
Disk identifier (GUID): 00000000-0000-0000-0000-000000000000
Logical sector size: 0x200  bytes ,First/Last usable sector: 34,61071326
Partition info successfully found
Formatting FRP...
Detected LINUX(Android) FRP : 0x000DE88000 (1.0MB) formatting...
Done.
Detected LINUX(Android) CACHE : 0x0203800000 (432.0MB) , formatting...
Done.
Detected LINUX(Android) USERDATA : 0x021E800000 (20.585GB) , formatting...
Done.
Done.
Done.
 

بلال العنابي

عضو أساسي
إنضم
24 ديسمبر 2018
المشاركات
940
مستوى التفاعل
408
النقاط
63
الإقامة
عنابة
رد: فتح قفل الشاشة و frp لهاتف اوبو a12

ما شاء الله
هل هناك نوعين من الذواكر لهذا الهاتف a12؟ emmc و ufs
 

.:: Mohamed Gsm ::.

:: مراقب البوكسات والبرامج المحمية ::
إنضم
2 أبريل 2017
المشاركات
5,098
مستوى التفاعل
5,328
النقاط
113
الإقامة
سيدي بلعباس
رد: فتح قفل الشاشة و frp لهاتف اوبو a12

بارك الله فيك
مشكل هذا الهاتف مسار clk يجب الحفر عليه لتوصيل isp
تشكر على هذا المجهود
 

cst_repair

:: عضو مميز ::
إنضم
2 يونيو 2013
المشاركات
280
مستوى التفاعل
370
النقاط
63
الإقامة
الجزائر الحبيبة
رد: فتح قفل الشاشة و frp لهاتف اوبو a12

نعم يستلزم الحفر لدلك لابد من ادوات خاصة مثل الميكروسكوب
 

.:: Sebti _ Gsm ::.

:: مراقب قسم بوكسات الجيتاق JTAG ::
إنضم
30 ديسمبر 2015
المشاركات
1,669
مستوى التفاعل
2,934
النقاط
113
الإقامة
Ghardaïa
رد: فتح قفل الشاشة و frp لهاتف اوبو a12

شكرا على عرض تجربتك

بارك الله فيك
 

Dr-GsM

عضو أساسي
إنضم
5 مارس 2015
المشاركات
1,284
مستوى التفاعل
627
النقاط
0
رد: فتح قفل الشاشة و frp لهاتف اوبو a12

شكرا لعرض التجربة بارك الله فيك
 

DZ-Djamel-GSM

:: مراقب عام ::
إنضم
9 يوليو 2018
المشاركات
5,452
مستوى التفاعل
4,334
النقاط
113
الإقامة
DzGsm
رد: فتح قفل الشاشة و frp لهاتف اوبو a12

السلام عليكم

بارك الله فيك عمل ممتاز أخي cst_repair شكراً لك
 

fethirx

عضو نشط
إنضم
1 فبراير 2015
المشاركات
42
مستوى التفاعل
63
النقاط
0
رد: فتح قفل الشاشة و frp لهاتف اوبو a12

تم الفتح على medusa pro

Please disconnect battery and USB cable.

Model Settings:
Interface : eMMC
Voltage : 2.2V
Bus Mode : 1 bit
Bus speed : 13 MHz

Connecting...
Device : Hynix eMMC hB8aP
Page size : 512 B
Block size : 512 B
Block count : 61071360
Size : 29.12 GB (29820.00 MB)
---------------------------------------------------------------
CID Info

CID : 90014A68423861503E035B2B25CC17D5
Manufacturer ID : 0X90
Device/BGA : BGA (Discrete embedded)
OEM/Application ID : 0X4A
Product name : hB8aP
Product revision : 0.3
Product serial number : (hex) 5B2B25CC
Manufacturing date : 01/2020
---------------------------------------------------------------
CSD Info

CSD : D02700328F5903FFFFFFFFEF8E400043
CSD structure : CSD version No. 1.2
SPEC version : 4.1, 4.2, 4.3, 4.4, 4.41, 4.5,
4.51, 5.0, 5.01, 5.1
Data read access time1: 15 ms
TRAN speed : 26 MHz
READ block length : 512 Bytes
WP group enable : YES
PERM_WRITE_PROTECT : NO
TMP_WRITE_PROTECT : NO
---------------------------------------------------------------
EXTCSD Info

Revision 1.8 (for MMC v5.1)
Erase block size : 512 Kbytes
Boot1 size : 4096 Kbytes
Boot2 size : 4096 Kbytes
RPMB size : 16384 Kbytes

Partition config : (0x48) 01001000
Boot partition enable : Boot partition 1
(Bus width = 8Bit)
Boot ACK : Boot acknowledge sent during boot operation Bit

Boot bus conditions : (0x02) 00000010
Boot bus width : x8 (sdr/ddr) bus width in boot operation mode
Reset boot bus conditions : Reset bus width to x1, single data rate and backward compatible timings after boot operation (default)
Boot mode : Use single data rate + backward compatible timings in boot operation (default)

RST_n function : (0x01) RST_n signal is permanently enabled

Partitioning support : Device supports partitioning features
Enhanced attribute : Device can have enhanced technological features in partitions and user data area.
Max enhanced data size: 15261696 Kbytes
Partitions attribute : 0x0
Part setting completed: 0x0
GP partition 1 size : 0 b
GP partition 2 size : 0 b
GP partition 3 size : 0 b
GP partition 4 size : 0 b
Enhanced area size : (0x0) 0 b
Enhanced area start : (0x0) 0 b

Backup EXT_CSD saved to file C:/Program Files/Medusa Pro Software/EXT_CSD Backups/hB8aP_14_01_2021_17_16_21.bin.
Connect successful.
---------------------------------------------------------------
SW: 2.1.8; FW: 1.24.
P00: GPT (00000000, 00000040) 32 KB
P01: boot_para (00000040, 00000800) 1024 KB
P02: recovery (00000840, 00020000) 64 MB
P03: para (00020840, 00000400) 512 KB
P04: opporeserve1 (00020C40, 00004000) 8 MB
P05: opporeserve2 (00024C40, 00020000) 64 MB
P06: opporeserve3 (00044C40, 00020000) 64 MB
P07: oppo_custom (00064C40, 00000800) 1024 KB
P08: expdb (00065440, 0000A000) 20 MB
P09: frp (0006F440, 00000800) 1024 KB
P10: nvcfg (0006FC40, 00010000) 32 MB
P11: nvdata (0007FC40, 00020000) 64 MB
P12: metadata (0009FC40, 00010000) 32 MB
P13: protect1 (000AFC40, 00004000) 8 MB
P14: protect2 (000B3C40, 000043C0) 8.469 MB
P15: seccfg (000B8000, 00004000) 8 MB
P16: persist (000BC000, 00018000) 48 MB
P17: sec1 (000D4000, 00001000) 2048 KB
P18: proinfo (000D5000, 00001800) 3072 KB
P19: md1img (000D6800, 00032000) 100 MB
P20: spmfw (00108800, 00000800) 1024 KB
P21: scp1 (00109000, 00000800) 1024 KB
P22: scp2 (00109800, 00000800) 1024 KB
P23: sspm_1 (0010A000, 00000800) 1024 KB
P24: sspm_2 (0010A800, 00000800) 1024 KB
P25: gz1 (0010B000, 00008000) 16 MB
P26: gz2 (00113000, 00008000) 16 MB
P27: nvram (0011B000, 00020000) 64 MB
P28: lk (0013B000, 00002800) 5 MB
P29: lk2 (0013D800, 00002800) 5 MB
P30: boot (00140000, 00010000) 32 MB
P31: logo (00150000, 00008000) 16 MB
P32: dtbo (00158000, 00008000) 16 MB
P33: tee1 (00160000, 00002800) 5 MB
P34: tee2 (00162800, 00005800) 11 MB
P35: odm (00168000, 00080000) 256 MB
P36: vendor (001E8000, 00230000) 1120 MB
P37: system (00418000, 00C00000) 6 GB
P38: vbmeta (01018000, 00004000) 8 MB
P39: cache (0101C000, 000D8000) 432 MB
P40: userdata (010F4000, 0292C7DF) 20.59 GB
P41: otp (03A207DF, 00015800) 43 MB
P42: flashinfo (03A35FDF, 00008000) 16 MB
Backuping nvdata partition...
Opening C:/Program Files/Medusa Pro Software/Backups/hB8aP_nvdata_0x7fc40_0x20000_14_01_2021_17_16_21.bin file...
Reading. Please wait... Done.
Elapsed time 00:00:47
SW: 2.1.8; FW: 1.24.

---------------------------------------------------------------
Searching Android build info...
Ok

Disk/Image size : 47c00000 bytes
Device sector size : 512 bytes
Partition offset : 4292608
Number of sectors : 12582912
Build ID : PPR1.180610.011
Release ID : 9
Architecture ABI : arm64-v8a
Architecture ABI List : arm64-v8a,armeabi-v7a,armeabi
Build Description : full_oppo6765_19451-user 9 PPR1.180610.011 eng.root.20201126.014332 release-keys

---------------------------------------------------------------
Reset operation finished
Reset operation finished
Disconnected.
 
أعلى