- إنضم
- 8 نوفمبر 2012
- المشاركات
- 223
- مستوى التفاعل
- 209
- النقاط
- 43
بعد تحديث الاخير لوجهة InfinityBox CM2SP2
اخيرا تم عمل ريست frp لعنديد kiowa cristal
وهنا طريقة اختيار بوت
في انتظار تحديثات قادمة واضافة خاصية سحب الفلاتشة
وهدا لوغ العملية
Card found : C73B4E26 , v0137
Infinity-Box Chinese Miracle II : SPD/USC Module [SP2] v2.00r1
Operation : Format FS / Reset Settings [ v2.00r1 ]
Mode : Default [ Reset Settings + FRP ]
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
BootVersion : SPRD3
Sedning Init Boot ...
ERROR : FDL Start Failed!
Error : Fail to boot FDL!
Unsupported device with selected fdl! Change settings!
Reconnect Power/Cable!
Operation : Format FS / Reset Settings [ v2.00r1 ]
Mode : Default [ Reset Settings + FRP ]
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
BootVersion : SPRD3
Sedning Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sedning Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : Control transfered!
Boot Done!
Wipe Ok : UserData
Wipe Ok : Cache
Wipe Ok : FRP
Reconnect Power/Cable!
Done!
Elapsed: 00:00:49
اخيرا تم عمل ريست frp لعنديد kiowa cristal
وهنا طريقة اختيار بوت
في انتظار تحديثات قادمة واضافة خاصية سحب الفلاتشة
وهدا لوغ العملية
Card found : C73B4E26 , v0137
Infinity-Box Chinese Miracle II : SPD/USC Module [SP2] v2.00r1
Operation : Format FS / Reset Settings [ v2.00r1 ]
Mode : Default [ Reset Settings + FRP ]
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
BootVersion : SPRD3
Sedning Init Boot ...
ERROR : FDL Start Failed!
Error : Fail to boot FDL!
Unsupported device with selected fdl! Change settings!
Reconnect Power/Cable!
Operation : Format FS / Reset Settings [ v2.00r1 ]
Mode : Default [ Reset Settings + FRP ]
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
BootVersion : SPRD3
Sedning Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sedning Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : Control transfered!
Boot Done!
Wipe Ok : UserData
Wipe Ok : Cache
Wipe Ok : FRP
Reconnect Power/Cable!
Done!
Elapsed: 00:00:49