مساعدة ممكن طريقة اصلاح الايمي wiko cink five

[MAWLOUD GSM]

السلام عليكم
لدي هاتف WIKO CINK FIVE
به مشكلة الايمي IMEI Invalid
والغريب انه عند قراءة انفو الجهاز عن طريق الميراكل يظهر انه سليم
وعند تشغيل الجهاز لا تجد الايمي
وبواسطة CM2 تظهر هذه الراسالة

Operation : Repair Security [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )

Wait for phone...
Phone found! [ 20 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 0000
BB_CPU_HW : 0000
BB_CPU_SW : 0000
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MTxxx
BROM Protocol Version : 05
Setting Service Mode ...
Init Service mode failed, something went wrong

Reconnect Power/Cable!


وعن محاولة اصلاحه عن طريق CM2 MT2 يعطي الرسالة التالية

Card found : E37DB9C0 , v0137
Infinity-Box Chinese Miracle MediaTek Service Module [ MTK ] v2.05

Load IDBase v123080 Ok!


Operation : Repair Security [ v2.05 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM20)
MODE : BOOTROM
PORT : 20
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6583 , SBID : 0x8A00 , HWVR : 0xCA01 , SWVR : 0x0001
TYPE : LEGACY MTK
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : BOOTROM
MODE : Wiko : SEC_6739 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6583
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...

DA : SYNC char NOT received!

Error : Fail to init protocol!
Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation!

Reconnect Power/Cable!

هل من حل من فضلكم

 

[syfou]

مدعوم على النسخة القديمة cm2mtk 1.58 جرب و أخبرنا....

 

[MAWLOUD GSM]

مدعوم على النسخة القديمة cm2mtk 1.58 جرب و أخبرنا....

على النسخة القديمة يعطي هذه الرسالة

Operation : Repair Security [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 20 ]
Sync...
Init Service mode failed, something went wrong :(

Reconnect Power/Cable!


Operation : Repair Security [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 20 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6583
BB_CPU_NME : [MediaTek] MT6583|6589_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.3.2 on BBID : 0x86
NAND Flash : NOT INSTALLED
eMMC Flash : 204A0190594E495879A11648196077BB
Initialize Memory ... 

[DA_ERROR] : DRAM Configure failed!
ErroCode : 0x2003
EMICFG_NOT_FOUND
TRY NOT HOLD VOLUME(+/-) KEYS ON CONNECT!
Boot Error!

Operation Failed
Elapsed: 00:00:08
Reconnect Power/Cable!


Operation : Repair Security [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 20 ]
Sync...
Init Service mode failed, something went wrong :(

Reconnect Power/Cable!

 

[.:: Mohamed Gsm ::.]

TRY NOT HOLD VOLUME(+/-) KEYS ON CONNECT!
Boot Error!

 

[MAWLOUD GSM]

TRY NOT HOLD VOLUME(+/-) KEYS ON CONNECT!
Boot Error!

البرنامج بخبرني بتجربة عدم الضغط على أزرار + رفع و - خفض الصوت
لكنني جربت عدم الضغط على اي زر لا يدخل التبويت ويبدأ الشحن
كذلك الضغط على زر خفض الصوت لا يدخل الجهاز لوضع التبويت
التبويت فقط بزر + رفع الصوت ،
المشكل انه حتى عند قراءة انفو الجهاز يعطي هته الرسالة

Chinese Miracle II  [MTK module] v 1.58

Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 20 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6583
BB_CPU_NME : [MediaTek] MT6583|6589_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.3.2 on BBID : 0x86
NAND Flash : NOT INSTALLED
eMMC Flash : 204A0190594E495879A11648196077BB
Initialize Memory ... 

[DA_ERROR] : DRAM Configure failed!
ErroCode : 0x2003
EMICFG_NOT_FOUND
TRY NOT HOLD VOLUME(+/-) KEYS ON CONNECT!
Boot Error!

Operation Failed
Elapsed: 00:00:11
Reconnect Power/Cable!