تم بنجاح ازالة قفل frp condor allure M1 بواسطة cm2mt2

الحالة
مغلق و غير مفتوح للمزيد من الردود.

mhamed2102

عضو أساسي
إنضم
19 سبتمبر 2015
المشاركات
576
مستوى التفاعل
207
النقاط
43
تم بنجاح ازالة قفل frp condor allure M1 بواسطة cm2mt2



1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : PreLoader USB VCOM (Android) (COM3)
MODE : PRELOADER PORT
PORT : 3
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6755 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0001
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : PRELOADER PORT
MODE : Gionee : M7 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_PL_CRYPTO.bin
AGENT : Found MT6755
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256,00 KB ]
DRAM: 0xC0000000 [ 3,00 GB ]

EMMC: 150100525831344D4207D019C6F984D1
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : RX14MB
EMMC:
BOOT1 : 0x00400000 [ 4,00 MB ]
BOOT2 : 0x00400000 [ 4,00 MB ]
RPMB : 0x00400000 [ 4,00 MB ]
USER : 0x747C00000 [ 29,12 GB ]

CHIP : MT6755 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : 841DFFDFABC862E393BACFFECAF93969

DA : USB : HIGH-SPEED

Boot done!

Format Ok : USERDATA
Format Ok : CACHE
Format Ok : RESET PROTECTION

Done!
Elapsed: 00:00:26

Reconnect Power/Cable!
عن طريق اختيار في القائمة
gionee
M7
ثم الى
service
 

boubedz

عضو
إنضم
6 يوليو 2017
المشاركات
7
مستوى التفاعل
3
النقاط
0
ممكن المشاركة بالصورة للعملية
نحن مبتدئين
و إن شاء الله أتعلم من أعضاء هدا المنتدى بشروحاتكم
 

Dr-GsM

عضو أساسي
إنضم
5 مارس 2015
المشاركات
1,284
مستوى التفاعل
627
النقاط
0
هذا فورمات اخي وليس حذف القفل هناك فرق
 

karim87

عضو أساسي
إنضم
9 يناير 2016
المشاركات
942
مستوى التفاعل
281
النقاط
63
شكرا لك اخي العملية ناجحة
 

MS-GSM

:: عضو محترف ::
إنضم
27 فبراير 2016
المشاركات
2,440
مستوى التفاعل
679
النقاط
0
الإقامة
Oran
السلام عليكم
نعم هذه عملية فورمات كما نوه الاخ Proglak هناك فرق بين حذف FRP و الفورمات و شكرا.
 

fouzi11

عضو أساسي
إنضم
14 فبراير 2015
المشاركات
192
مستوى التفاعل
78
النقاط
28
الإقامة
الجزائر زغاية
يمكنك ازالة القفل من غير الفورماط او القراءة لقفل الشاشة احسن ومشكور على الشرح
 

driss_dz

:: Super User::, ,
إنضم
15 مارس 2012
المشاركات
1,204
مستوى التفاعل
2,773
النقاط
0
الإقامة
ilizi
تمت العملية بواسطة nck
Exe version: NCKBox AndroidMTK 1.8.9.2
Selected model: ELBRUS
Action: Reset FRP
Reinsert phone battery.
Battery must be charged.
Phone must be off with battery inside.
Please insert USB cable now...
Detected : MediaTek PreLoader USB VCOM (Android) (COM55)
Boot mode: Preloader
Phone detected...Please wait
Using Algo 3.
Helio MT6755 phone detected, swithing to helio api
BBCHIP MT6755
EMMC FW VERSION: 00:00:00:00:00:00:00:00
EMMC CID: 15010052583134 : 000000000000000000
EMMC UA SIZE: 0x747c00000
BOOT STYLE: EMMC BOOT
FULL LENGTH: 0x748800000 [29.133 GB]
-Reading GPT Drive OK
Checking data, wait...

Erasing FRP, wait...
FRP Reset Done.
Wait untill phone will start charging.
All done.
 

samir21

عضو
إنضم
26 ديسمبر 2016
المشاركات
10
مستوى التفاعل
2
النقاط
0
بارك الله فيك اخي. مشكووووور
 

cherif75

عضو
إنضم
11 يناير 2018
المشاركات
23
مستوى التفاعل
2
النقاط
0
زر خفض الصوت ىمر عادى لا تاشر على اي شيء
Card found : 23255471 , v0137
Infinity-Box Chinese Miracle MediaTek Service Module [ MTK ] v2.03

Load IDBase v123080 Ok!


Operation : Identify [ v2.03 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM28)
MODE : PRELOADER PORT
PORT : 28
Error : Failed to open port!

Error : Fail to init protocol!
Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation!

Reconnect Power/Cable!


Operation : Identify [ v2.03 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM28)
MODE : PRELOADER PORT
PORT : 28
Error : Failed to open port!

Error : Fail to init protocol!
Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation!

Reconnect Power/Cable!


Operation : Identify [ v2.03 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM28)
MODE : PRELOADER PORT
PORT : 28
Error : Failed to open port!

Error : Fail to init protocol!
Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation!

Reconnect Power/Cable!


Operation : Identify [ v2.03 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MTK USB Port (COM38)
MODE : BOOTROM
PORT : 38
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6755 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0001
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : BOOTROM
MODE : Gionee : M7 | Manual : Disabled
BROM : SLA

BROM : Selected Auth/Cert not accepted by device!
Check previous message for more info!

Reconnect Power/Cable!


Operation : Reset Settings/Format FS [ v2.03 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM28)
MODE : PRELOADER PORT
PORT : 28
Error : Failed to open port!

Error : Fail to init protocol!
Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation!

Reconnect Power/Cable!


Operation : Reset Settings/Format FS [ v2.03 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM28)
MODE : PRELOADER PORT
PORT : 28
Error : Failed to open port!

Error : Fail to init protocol!
Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation!

Reconnect Power/Cable!


Operation : Reset Settings/Format FS [ v2.03 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MTK USB Port (COM38)
MODE : BOOTROM
PORT : 38
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6755 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0001
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : BOOTROM
MODE : Gionee : M7 | Manual : Disabled
BROM : SLA

BROM : Selected Auth/Cert not accepted by device!
Check previous message for more info!

Reconnect Power/Cable!


Operation : Reset Settings/Format FS [ v2.03 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MTK USB Port (COM38)
MODE : BOOTROM
PORT : 38
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6755 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0001
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : BOOTROM
MODE : Gionee : M7 | Manual : Disabled
BROM : SLA

BROM : Selected Auth/Cert not accepted by device!
Check previous message for more info!

Reconnect Power/Cable!


Operation : Identify [ v2.03 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MTK USB Port (COM38)
MODE : BOOTROM
PORT : 38
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6755 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0001
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : BOOTROM
MODE : 0_base : BASE_v1712 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6755
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : INFINITY
EMI : SRC : INFINITY-BOX_INTERNAL_EMIDB_v0
EMI : CNT : 0009
EMI : Init EMI from INTERNAL DB
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256,00 KB ]
DRAM: 0xC0000000 [ 3,00 GB ]

EMMC: 150100525831344D4207D4CBC6439425
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : RX14MB
EMMC:
BOOT1 : 0x00400000 [ 4,00 MB ]
BOOT2 : 0x00400000 [ 4,00 MB ]
RPMB : 0x00400000 [ 4,00 MB ]
USER : 0x747C00000 [ 29,12 GB ]

CHIP : MT6755 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : F60BE8076749640F92F52E2BF33EE8C5

DA : USB : FULL-SPEED
DA : USB : Change Port Speed
PTFN : MediaTek DA USB VCOM (Android) (COM39)
MODE : PRELOADER PORT
PORT : 39

Boot done!

Board Platform : mt6755
Build Time : 1500624688
Display ID : Allure_M1
Patch Level : NRD90M
Product Info : gnsz6755_66_n
Ver. CodeName : REL
Ver. Release : 7.0
Sec. Patch : 2017-06-05
Product Board : Allure_M1
Product Brand : Condor
Product Device : Allure_M1
Product Manfct : SPA Condor Electronics
Product Model : Allure M1
Product Name : Allure_M1

USERDATA : ENCRYPTED


Done!
Elapsed: 00:00:16

Operation : Reset Settings/Format FS [ v2.03 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MTK USB Port (COM38)
MODE : BOOTROM
PORT : 38
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6755 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0001
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : BOOTROM
MODE : 0_base : BASE_v1712 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6755
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : INFINITY
EMI : SRC : INFINITY-BOX_INTERNAL_EMIDB_v0
EMI : CNT : 0009
EMI : Init EMI from INTERNAL DB
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256,00 KB ]
DRAM: 0xC0000000 [ 3,00 GB ]

EMMC: 150100525831344D4207D4CBC6439425
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : RX14MB
EMMC:
BOOT1 : 0x00400000 [ 4,00 MB ]
BOOT2 : 0x00400000 [ 4,00 MB ]
RPMB : 0x00400000 [ 4,00 MB ]
USER : 0x747C00000 [ 29,12 GB ]

CHIP : MT6755 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : F60BE8076749640F92F52E2BF33EE8C5

DA : USB : FULL-SPEED
DA : USB : Change Port Speed
PTFN : MediaTek DA USB VCOM (Android) (COM39)
MODE : PRELOADER PORT
PORT : 39

Boot done!

Format Ok : USERDATA
Format Ok : CACHE
Format Ok : RESET PROTECTION
Format Ok : USERDATA

Done!
Elapsed: 00:00:28

Reconnect Power/Cable!
 

bestAssem

عضو نشط
إنضم
16 أكتوبر 2016
المشاركات
87
مستوى التفاعل
21
النقاط
0
نجحت معي العملية مشكور أخي
 

MAWLOUD GSM

عضو أساسي
إنضم
30 مايو 2017
المشاركات
566
مستوى التفاعل
269
النقاط
63
الإقامة
أرض الله الواسعة
رد: تم بنجاح ازالة قفل frp condor allure M1 بواسطة cm2mt2

تمت العملية بنجاح 100%
مشكور وبارك الله فيك
للاشارة :
يمكنك نسخ ملف التبويت واعادة تسميته بملف CONDOR M1
ولصقه بمسار ملفات التبويت ليسهل اختياره لاحقا ، كما في الصورة

917428373.jpg
 
الحالة
مغلق و غير مفتوح للمزيد من الردود.
أعلى