مساعدة هل توجد فلاشة p6 plus بهذا الاصدار

bah999

عضو أساسي
إنضم
5 يونيو 2014
المشاركات
803
مستوى التفاعل
819
النقاط
93
الإقامة
https://t.me/pump_upp
هل توجد فلاشة p6 plus بهذا الاصدار T5925

السلام عليكم
يقول صاحب الجهاز انه كان يقوم بالتحديث الهوائي
فجأة نفذت البطارية و هو لم يكمل التحديث
فبقي يعيد التشغيل

المشكل لا يقبل اي تحديث T5832 او
T5892

و الاصدار الدي نزل به T5925 و بقي عالق به و لا يقبله الا هو

غير جيد backup

MT6735__condor__PGN522__PGN522__6.0__WBL7355AC_020 2_T5925

كود:
Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand : condor
Device Model : PGN522
Device CPU : MT6735
Device IntName : PGN522
Device Version : 6.0
Device Compile : 23-12-2016 8:12:06
Device Project : WBL7355AC_0202_T5925
Device ExtInfo : PGN522
 
التعديل الأخير:

samy08

عضو أساسي
إنضم
21 فبراير 2013
المشاركات
275
مستوى التفاعل
548
النقاط
0
الإقامة
IN DA CLUB
هل تسطيع تزويدنا بالنسخة t5892 بارك الله فيك لان بهدا الكلام يصبح للهاتف ب4 اصدارات للفرموار
 

technomedia

عضو
إنضم
19 مارس 2018
المشاركات
23
مستوى التفاعل
4
النقاط
0
الإقامة
عين مليلة
نفس المشكلة هنا ؟ لا وجود لهذه الفلاشة في الانترنت ، أي مساعدة سأكون شاكرا لها
هذا لوق التعريف condor p6 plus
Chinese Miracle II [MTK module] v 1.58

Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 18 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6735
BB_CPU_NME : [MediaTek] MT6735_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 460001154D323145CB480742474F3C61
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM21E
[eMMC] : FLASH_CID : 150100464531324D420748CB613C4447
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB [eMMC 16 GiB]
DEV RID : 0x5BFC63C52758A51C42F935A2F0C84BF7
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand : condor
ProdName : PGN522
ProdModel : PGN522
Device : PGN522
AndroidVer: 6.0
MTKxCPU : MT6735
MTKxPRJ : WBL7355AC_0202_T5925

Done!
Elapsed: 00:00:08
Reconnect Power/Cable!
 

IMAX 1979

عضو أساسي
إنضم
8 مارس 2016
المشاركات
793
مستوى التفاعل
870
النقاط
93
الإقامة
سيدي بلعباس
153070675657851.png


جاري الرفع ...
 
التعديل الأخير:

technomedia

عضو
إنضم
19 مارس 2018
المشاركات
23
مستوى التفاعل
4
النقاط
0
الإقامة
عين مليلة
لا أدري ما المشكلة يقول بأن هذا الفلاش سيتسبب بموت الهاتف ربما لا يوجد تطابق ؟

Chinese Miracle II [MTK module] v 1.58

Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Device boot not done
Check Drivers
Try again

Boot Error!

Operation Failed
Elapsed: 00:00:27
Reconnect Power/Cable!


Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Device boot not done
Check Drivers
Try again

Boot Error!

Operation Failed
Elapsed: 00:00:27
Reconnect Power/Cable!


Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Device boot not done
Check Drivers
Try again

Boot Error!

Operation Failed
Elapsed: 00:00:27
Reconnect Power/Cable!


Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Device boot not done
Check Drivers
Try again

Boot Error!

Operation Failed
Elapsed: 00:00:27
Reconnect Power/Cable!


Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Device boot not done
Check Drivers
Try again

Boot Error!

Operation Failed
Elapsed: 00:00:27
Reconnect Power/Cable!


Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 25 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6735
BB_CPU_NME : [MediaTek] MT6735_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 460001154D323145CB480742474F3C61
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM21E
[eMMC] : FLASH_CID : 150100464531324D420748CB613C4447
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB [eMMC 16 GiB]
DEV RID : 0x5BFC63C52758A51C42F935A2F0C84BF7
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand : condor
ProdName : PGN522
ProdModel : PGN522
Device : PGN522
AndroidVer: 6.0
MTKxCPU : MT6735
MTKxPRJ : WBL7355AC_0202_T5925

Done!
Elapsed: 00:00:12
Reconnect Power/Cable!


Scatter Load Ok , BaseBand : MT6737 , Project : gionee6735m_65u_m0 , Storage : EMMC
Files found : 11 , Set to Flash : 10
Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand : condor
Device Model : PGN522
Device CPU : MT6735
Device IntName : PGN522
Device Version : 6.0
Device Compile : 12/23/2016 8:12:06
Device Project : WBL7355AC_0202_T5925
Device ExtInfo : PGN522
Ready to Flash!

Operation : Flash [ v1.58 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 25 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6735
BB_CPU_NME : [MediaTek] MT6735_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 460001154D323145CB480742474F3C61
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM21E
[eMMC] : FLASH_CID : 150100464531324D420748CB613C4447
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB [eMMC 16 GiB]
DEV RID : 0x5BFC63C52758A51C42F935A2F0C84BF7
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6737 , Project : gionee6735m_65u_m0 , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled
Setting : HW verify : Enabled

BL : Check HW compatibility
BL : BBID NOT supported by BootLoader!
[BL_ERROR] : BBID : Break Flashing! This Firmware will kill phone!

Operation Failed
Elapsed: 00:00:16
Reconnect Power/Cable!
 

moherahma

عضو
إنضم
17 أغسطس 2013
المشاركات
8
مستوى التفاعل
2
النقاط
3
لا أدري ما المشكلة يقول بأن هذا الفلاش سيتسبب بموت الهاتف ربما لا يوجد تطابق ؟

Chinese Miracle II [MTK module] v 1.58

Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Device boot not done
Check Drivers
Try again

Boot Error!

Operation Failed
Elapsed: 00:00:27
Reconnect Power/Cable!


Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Device boot not done
Check Drivers
Try again

Boot Error!

Operation Failed
Elapsed: 00:00:27
Reconnect Power/Cable!


Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Device boot not done
Check Drivers
Try again

Boot Error!

Operation Failed
Elapsed: 00:00:27
Reconnect Power/Cable!


Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Device boot not done
Check Drivers
Try again

Boot Error!

Operation Failed
Elapsed: 00:00:27
Reconnect Power/Cable!


Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Device boot not done
Check Drivers
Try again

Boot Error!

Operation Failed
Elapsed: 00:00:27
Reconnect Power/Cable!


Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 25 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6735
BB_CPU_NME : [MediaTek] MT6735_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 460001154D323145CB480742474F3C61
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM21E
[eMMC] : FLASH_CID : 150100464531324D420748CB613C4447
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB [eMMC 16 GiB]
DEV RID : 0x5BFC63C52758A51C42F935A2F0C84BF7
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand : condor
ProdName : PGN522
ProdModel : PGN522
Device : PGN522
AndroidVer: 6.0
MTKxCPU : MT6735
MTKxPRJ : WBL7355AC_0202_T5925

Done!
Elapsed: 00:00:12
Reconnect Power/Cable!


Scatter Load Ok , BaseBand : MT6737 , Project : gionee6735m_65u_m0 , Storage : EMMC
Files found : 11 , Set to Flash : 10
Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand : condor
Device Model : PGN522
Device CPU : MT6735
Device IntName : PGN522
Device Version : 6.0
Device Compile : 12/23/2016 8:12:06
Device Project : WBL7355AC_0202_T5925
Device ExtInfo : PGN522
Ready to Flash!

Operation : Flash [ v1.58 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 25 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6735
BB_CPU_NME : [MediaTek] MT6735_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 460001154D323145CB480742474F3C61
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM21E
[eMMC] : FLASH_CID : 150100464531324D420748CB613C4447
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB [eMMC 16 GiB]
DEV RID : 0x5BFC63C52758A51C42F935A2F0C84BF7
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6737 , Project : gionee6735m_65u_m0 , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled
Setting : HW verify : Enabled

BL : Check HW compatibility
BL : BBID NOT supported by BootLoader!
[BL_ERROR] : BBID : Break Flashing! This Firmware will kill phone!

Operation Failed
Elapsed: 00:00:16
Reconnect Power/Cable!

اخي يمكنك تحميلها من موقع كوندور مباشرتا
 

stored77

عضو نشط
إنضم
28 مارس 2018
المشاركات
66
مستوى التفاعل
15
النقاط
0
الإقامة
algeria
بارك الله فيك وجزاك الله كل خير
لو سمحت محتاج مخطط هاتف P6 Plus
 

selmigsm

عضو أساسي
إنضم
22 ديسمبر 2018
المشاركات
326
مستوى التفاعل
57
النقاط
28
ولكن يجيب ان تكون بنفس الاصدار والا سيموت الهاتف
 

allaoua050

عضو نشط
إنضم
28 مارس 2020
المشاركات
34
مستوى التفاعل
2
النقاط
8
رد: هل توجد فلاشة p6 plus بهذا الاصدار

ماهو رابط تحميل الفلاشات لهاتف الكوندور p6 plus من موقع كوندور وشكرا
 
أعلى