info.gsm
عضو أساسي
- إنضم
- 25 ديسمبر 2015
- المشاركات
- 446
- مستوى التفاعل
- 864
- النقاط
- 0
Condor Griffe T2 (SP530) SPRD PAC + Nvram
Check/Read Info
كود:
[LEFT]Chinese Miracle II [SPD module] v 1.27
Set mode to : SP [SC983x] eMMC [Generic Android 7.x]
Operation : Check/Read Info [ v1.27 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
-> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable
==== Wait for phone...
Phone found! [ 6 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC983x eMMC Loader v5.0 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FLASH : eMMC Flash , Structure : Ok!
Reading extended info ...
Model Name : SP530
Model Brand : Condor
Model Device: SP530
AndrVersion : 7.0
BaseBand CPU: ZSL866_AN
CompileDate : 22-07-2017 11:28:17
Project Ver : NRD90M release-keys
Model Ext : Griffe T2
ExtraInfo : HWInfo not exists, normal phone
Elapsed: 00:00:35
Reconnect Power/Cable!
[/LEFT]
Read FullFlash
كود:
[LEFT]
Operation : Read FullFlash [ v1.27 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
-> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable
==== Wait for phone...
Phone found! [ 6 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC983x eMMC Loader v5.0 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!
[FW_READER] : Prepare Ok!
- > Wait phone connected ...
Phone found! [ 6 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC983x eMMC Loader v5.0 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
- > Wait phone connected ...
Phone found! [ 6 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC983x eMMC Loader v5.0 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Model Name : SP530
Model Brand : Condor
Model Device: SP530
AndrVersion : 7.0
BaseBand CPU: ZSL866_AN
Project Ver : NRD90M release-keys
Model Ext : Griffe T2
[Read Mode] : HSUSB : 0x3000
[FW_READER] : Reading Firmware Now ...
[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : nvitem_l.bin
[Read Ok] : sc983x_cp1.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : l__WPH_arm7.bin
[Read Ok] : PM_arm7_sys.bin
[Read Ok] : logo_720x1280.bin
[Read Ok] : fblogo_720x1280.bin
[Read Ok] : wcn_fdl.bin
[Read Ok] : AA_MARLIN.bin
[Read Ok] : boot.img
[Read Ok] : trustos.bin
[Read Ok] : vmm.bin
[Read Ok] : system.img
[Read Ok] : sysinfo.img
[Build Ok] : cache.img
[Read Ok] : recovery.img
[Build Ok] : userdata.img
AndroidInfo created
Firmware Size : 2709 MiB
Saved to : C:\Users\INFO.GSM\Desktop\ZSL866_AN_SP530_7.0_NRD90M_release-keys_Griffe_T2\
Done!
Elapsed: 00:11:31
Reconnect Power/Cable![/LEFT]Read NV
كود:
[LEFT]
Operation : Read NV [ v1.27 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
-> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable
==== Wait for phone...
Phone found! [ 6 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC983x eMMC Loader v5.0 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Detected eMMC Flash , Structure detect Ok!
Read LTEx NV #1
Read Ok , 0x1AFA4
Saved to : C:\Users\INFO.GSM\Desktop\CX77xx_SPDNV.spdnv
Elapsed: 00:00:38
Reconnect Power/Cable!
[/LEFT]Convert InfinitySC to SPRD PAC
كود:
[LEFT]
Operation : Convert InfinitySC to SPRD PAC [ v1.27 ]
Target : ZSL866_AN_SP530_7.0_NRD90M_release-keys_Griffe_T2
Step #1 : Identify
MEMORY : eMMC
LAYOUT : eMMC NORMAL
Step #2 : Select logic
Select Logic : SC5300
Step #3 : Processing data
Build PAC
[ADD FILE] : nvitem_l.bin
[ADD FILE] : prodnv.img
[ADD FILE] : u-boot-spl-16k.bin
[ADD FILE] : sc983x_cp1.bin
[ADD FILE] : DSP_DM_Gx.bin
[ADD FILE] : DSP_DM_Gx.bin
[ADD FILE] : l__WPH_arm7.bin
[ADD FILE] : PM_arm7_sys.bin
[ADD FILE] : logo_720x1280.bin
[ADD FILE] : fblogo_720x1280.bin
[ADD FILE] : wcn_fdl.bin
[ADD FILE] : AA_MARLIN.bin
[ADD FILE] : boot.img
[ADD FILE] : system.img
[ADD FILE] : sysinfo.img
[ADD FILE] : cache.img
[ADD FILE] : recovery.img
[ADD FILE] : userdata.img
[ADD FILE] : u-boot.bin
Build Ok! Result : 0x001A
Sign PAC ...
Sign Ok! FW compiled!
Elapsed: 00:02:11
Saved to : ZSL866_AN_SP530_7.0_NRD90M_release-keys_Griffe_T2.pac
Done!
[/LEFT]SPRD PAC
SP530_V15.0_20170706
https://mega.nz/#!aogwwTiI!6hOm0ndoKzwRkf_vihvbBzyQilfaLvqJn0WjXENeZX4
Nvram
https://mega.nz/#!upQV2aZD!qQAHzRqtz2wMqT9VftK00HERO6vJRC-1RX4MQr0_hZU
التعديل الأخير:
