مشكل في فك شفرة d100 mobilis

[Abou Houssam]

السلام عليكم
عند محاولة ادخال nck
عبر 2945=*100=
وعند الضغط على verrouialage reseau
تاتي رسالة votre téléphone n'est pas personnalisé
ما الحل

[MBtech]

استعمل lgtool مثلا او اي بوكس يدعم فك الشفرة المباشر و ليس قراءة الكود
لان الجهاز استقبل 10 أكواد خاطئة

بالتوفيق

[Abou Houssam]

ممكن الطريقة على lgtool

[MBtech]

connect
ركب الجهاز على ال usb بدون بطارية أظن و بالضغط على زر خفض الصوت
و بعدها Unlock

[Abou Houssam]

Using COMPORT: COM5
Analising USB Configuration...
Connect powered off MTK Device to USB cable... You have 20 seconds.
USB Serial COM Attached to system...
COM Port short name : COM51
COM Port full name : LGE ANDROIDNET USB SERIAL PORT
COM Port hardware id : USB\VID_1004&PID_61F1&REV_0100&MI_02
Open port COM51...
Send start CMD commands...done
Read HW_CODE...done
HW_CODE: 0x6572
Read HW_SW_VER...done
HW_SUB_CODE: 0x8A00
HW_VER: 0xCA01
SW_VER: 0x0000
GetEntryRegion...done
Get battery status...done
Disable WDT...done
Send DA Agent...done
Wait DA response...done
Send storage device and external ram device config...done
Detect NAND Flash...done
Get target inforamtion...done
Booting OK
EMMC Config:
EMMC rpmb size: 512kb
EMMC boot1 size: 4096kb
EMMC boot2 size: 4096kb
EMMC user area size: 3728 Mb
Read logical partitions info...done
Totally detected partitions: 32
Searching security blocks...ok
Reading Security...done
IMEI A: 35580306166358
IMEI B: 35030526000000
Bluetooth address:0C48852F8C02
Wi-Fi MAC address:0C4885B2BD48
SML Data: 000
Updating Security Flags...
Write MISC2 Partition...done
Update Security Info OK

يبقى هكذا

[yacine_41]

octoplus او cm2 في ثوان

[Abou Houssam]

لدي cm2
يعطيني الكود لكن المشكل لا يمكن ادخاله

[Abou Houssam]

Wait for phone...
Phone found! [ 51 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use SecMode DA
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 1501004E35585A4D42069B8FD6D91275
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMZX5
[eMMC] : FLASH_CID : 1501004E35585A4D42069B8FD6D91275
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB]
DEV RID : 0xB627A59359E37A60DC3C9210FAE0CDFE
INT RAM : 0x00020000
EXT RAM : 0x20000000 [512 MiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


UNCK : 9176881186117152
USIM : 2310853993306272
NSCK : 6340617776624417
SPCK : 4770927508031202
UCCK : 7555039987035915
UHCK : 0000000000000000

Done!
Elapsed: 00:00:15
Reconnect Power/Cable!

[yacine_41]

اعمل ديراكت انلوك وليس قراءة كود

[Abou Houssam]

لا توجد في cm2 direct unlock