بعد تلحيم كل الاسلاك بعناية و معرفة id الهاتف
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Resurrector: [Huawei U8825D V1.0.4710.49481]
Connecting to the dead body...OK
Set I/O Voltage reads as 2.59V, TCK Frequency is 5 kHz
Detected dead body ID: 0x007700E1
قمت بمايلي
1- Analyze jtag chain
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Resurrector: [Huawei U8825D V1.0.4710.49481]
Connecting to the target...OK
Set I/O Voltage reads as 2.60V, TCK Frequency is 5 kHz
Following devices are found on the JTAG chain:
Device on TAP #0: ID = 0x007700E1, IR Length = 0x04 bits
Total IR length: 0x0004 bits
Analizing IDCODE(s) of the JTAG scan chain:
1. 0x007700E1: Qualcomm MSM8225, H/W Rev. #0
2-Resurrection
لمعرفة الموديلات التي لها نفس ID: 0x007700E1
وجدت عدد من الموديلات بعد استظهارها بواسطة searsh for dll
3* اخترت كل الموديلات واحدا واحدا وفي كل مرة اقوم بتغيير speed
النتيجة اني لم اتمكن من قراءة الفلاش
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Resurrector: [Huawei U8825D V1.0.4710.49481]
Connecting to the dead body...OK
Detected dead body ID: 0x007700E1 - CORRECT!
Set I/O Voltage reads as 2.59V, TCK Frequency is 5 kHz
Settings Code: 0x00010100000000000000000080000000
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...FAILED
ERROR: Read/Write memory failed during H/W Init.
----------------------------------------------------------------------------------------------------------------------------
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Resurrector: [Huawei U8825D V1.0.4710.49481]
Connecting to the dead body...OK
Detected dead body ID: 0x007700E1 - CORRECT!
Set I/O Voltage reads as 2.59V, TCK Frequency is 5 kHz
Settings Code: 0x00010100000000000000000080000000
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...FAILED
ERROR: No response from the RIFF Box.
----------------------------------------------------------------------------------------------------------------------------
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Resurrector: [Huawei U8825D V1.0.4710.49481]
Connecting to the dead body...OK
Detected dead body ID: 0x007700E1 - CORRECT!
Set I/O Voltage reads as 2.59V, TCK Frequency is 5 kHz
Settings Code: 0x00010100000000000000000080000000
Resurrection sequence started.
Establish communication with the phone...FAILED
ERROR(0x44): Communication is not established. Terminating.
----------------------------------------------------------------------------------------------------------------------------
مع ملاحظة ان الطاب سليم 100/100 من نوع +q7a الجديد